Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Subinterface Counter

Is it possible to see the traffic rate on a subinterface. From the show interfaces I can see only combined traffic on main interface.

GigabitEthernet2/1 is up, line protocol is up

Hardware is Gigabit Ethernet, address is 0018.7360.8181 (bia 0018.7360.8181)

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, rely 255/255, load 4/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Auto Duplex, 1000Mbps, link type is autonegotiation, media type is LX

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:00, output 00:00:00, output hang never

Last clearing of "show interface" counters never

Queueing strategy: PXF First-In-First-Out

Output queue 0/8192, 1 drops; input queue 0/75, 0 drops

5 minute input rate 9187000 bits/sec, 4091 packets/sec

5 minute output rate 19331000 bits/sec, 4196 packets/sec

5419310826 packets input, 1797388924287 bytes, 0 no buffer

Received 1452867 broadcasts, 0 runts, 0 giants, 0 throttles

1 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog, 2257891 multicast, 0 pause input

5782916690 packets output, 3612985880133 bytes, 0 underruns

0 output errors, 0 collisions, 53 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier, 0 pause output

0 output buffer failures, 0 output buffers swapped out

GigabitEthernet2/1.5 is up, line protocol is up

Hardware is Gigabit Ethernet, address is 0018.7360.8181 (bia 0018.7360.8181)

Description: Connected to 3750 Mgmt

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, rely 255/255, load 4/255

Encapsulation 802.1Q Virtual LAN, Vlan ID 5.

ARP type: ARPA, ARP Timeout 04:00:00

Xconnect switched:

Pkts In 0, Chars In 0, Pkts Out 0, Chars Out 0

GigabitEthernet2/1.6 is up, line protocol is up

Hardware is Gigabit Ethernet, address is 0018.7360.8181 (bia 0018.7360.8181)

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, rely 255/255, load 4/255

Encapsulation 802.1Q Virtual LAN, Vlan ID 6.

ARP type: ARPA, ARP Timeout 04:00:00

Xconnect switched:

Pkts In 0, Chars In 0, Pkts Out 0, Chars Out 0

GigabitEthernet2/1.18 is up, line protocol is up

Hardware is Gigabit Ethernet, address is 0018.7360.8181 (bia 0018.7360.8181)

Description: Connected to Mgmt-Sub_3550

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, rely 255/255, load 4/255

Encapsulation 802.1Q Virtual LAN, Vlan ID 18.

ARP type: ARPA, ARP Timeout 04:00:00

Xconnect switched:

Pkts In 0, Chars In 0, Pkts Out 0, Chars Out 0

Thanks,

Prakash

1 REPLY
New Member

Re: Subinterface Counter

I have got the following output by giving show vlan command...

UMS-10720#sh vlan 806

VLAN ID: 806 (IEEE 802.1Q Encapsulation)

Protocols Configured: Received: Transmitted:

IP 14418742 16980286

MPLS 0 0

VLAN trunk interfaces for VLAN ID 806:

GigabitEthernet2/1.806 (806)

IP: 213.130.120.105

Total 0 packets, 0 bytes input

Total 134613 packets, 15714655 bytes output

But I am confused on second last line where it says 0 packets and 0 bytes input.

Is there SNMP support for subinterfaces? I use 12.0(32)S4. I could not find anything on feature navigator.

Thanks,

Prakash

1377
Views
0
Helpful
1
Replies