Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Sup V-10GE question

I have 2 Sup V-10GE in each of my C4507R-E switches. They are in SSO mode. Te3/1 is connected. Te 4/1 is connected. Te3/2 is inactive. Te 4/2 is inactive.

Can I use Te 3/2 and Te 4/2 in channel mode for a Nexxus switch uplink?

I have 2 of these C4507R-E as my core switches and will want to do the same identical setup to the 2nd core switch

  • LAN Switching and Routing
3 ACCEPTED SOLUTIONS

Accepted Solutions
Cisco Employee

Re: Sup V-10GE question

If I am not wrong then

Dual uplinks are supported in the following modes of operation:

1) If there are two sups in the device, you can have the first TenGig of
each sup active and acting as an uplink.

or 

2) If there is a single sup in the chassis, then two interfaces on the same
sup would be active and acting as an uplink.

You cannot have dual uplinks on a single sup active when dual sups are
installed in the system.

Cisco Employee

Re: Sup V-10GE question

Check This out

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/52sg/configuration/guide/RPR.html#wp1097897

When you select 10-Gigabit Ethernet uplinks on WS-X4516-10GE and WS-X4013+10GE Supervisor Engines in RPR or SSO mode, only TenGigabitEthernet 1/1 and 2/1 interfaces are available. Similarly, when you select Gigabit Ethernet uplinks, only GigabitEthernet 1/3, 1/4, 2/3, and 2/4 interfaces are available. When you select to use both uplinks concurrently, TenGigabitEthernet 1/1 and 2/1 interfaces and GigabitEthernet 1/3, 1/4, 2/3, and 2/4 interfaces are available.

Hope this helps.

Cisco Employee

Re: Sup V-10GE question

Thats is correct.

4 REPLIES
Cisco Employee

Re: Sup V-10GE question

If I am not wrong then

Dual uplinks are supported in the following modes of operation:

1) If there are two sups in the device, you can have the first TenGig of
each sup active and acting as an uplink.

or 

2) If there is a single sup in the chassis, then two interfaces on the same
sup would be active and acting as an uplink.

You cannot have dual uplinks on a single sup active when dual sups are
installed in the system.

Cisco Employee

Re: Sup V-10GE question

Check This out

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/52sg/configuration/guide/RPR.html#wp1097897

When you select 10-Gigabit Ethernet uplinks on WS-X4516-10GE and WS-X4013+10GE Supervisor Engines in RPR or SSO mode, only TenGigabitEthernet 1/1 and 2/1 interfaces are available. Similarly, when you select Gigabit Ethernet uplinks, only GigabitEthernet 1/3, 1/4, 2/3, and 2/4 interfaces are available. When you select to use both uplinks concurrently, TenGigabitEthernet 1/1 and 2/1 interfaces and GigabitEthernet 1/3, 1/4, 2/3, and 2/4 interfaces are available.

Hope this helps.

New Member

Re: Sup V-10GE question

Thanks for the replies. Since I do have it in SSO mode I can only use Te 3/1 and Te 4/1.

Cisco Employee

Re: Sup V-10GE question

Thats is correct.

512
Views
0
Helpful
4
Replies
This widget could not be displayed.