Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

SUP720 error

I keep getting the following error on my 6506 running Sup720. PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 6 is experiencing the following error: Bus Asic #0 transient Pb error. Recovered (0x0002, 0x0000). Cisco error message decoder shows the following: An error condition was detected by the line card firmware and the supervisor is being informed about it. How do I upgrade the firmware on my sup720? Currently running s72033-advipservicesk9_wan-mz.122-18.SXF10a.bin. sh mod on switch A is Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 6 Firewall Module WS-SVC-FWM-1 SAD084409GR

2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1026SMX3

6 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1031XABY

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0003.3234.ecba to 0003.3234.ecc1 3.0 7.2(1) 3.2(10) Ok

2 0017.5916.2d14 to 0017.5916.2d43 2.3 12.2(14r)S5 12.2(18)SXF1 Ok

6 0013.c31f.f160 to 0013.c31f.f163 4.4 8.1(3) 12.2(18)SXF1 Ok

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

2 Centralized Forwarding Card WS-F6700-CFC SAL1209HMM8 4.0 Ok

6 Policy Feature Card 3 WS-F6K-PFC3B SAL0943407P 2.1 Ok

6 MSFC3 Daughterboard WS-SUP720 SAL094659X8 2.3 Ok

sh mod on switch B is Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 6 Firewall Module WS-SVC-FWM-1 SAD084409GR

2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1026SMX3

6 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1031XABY

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0003.3234.ecba to 0003.3234.ecc1 3.0 7.2(1) 3.2(10) Ok

2 0017.5916.2d14 to 0017.5916.2d43 2.3 12.2(14r)S5 12.2(18)SXF1 Ok

6 0013.c31f.f160 to 0013.c31f.f163 4.4 8.1(3) 12.2(18)SXF1 Ok

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

2 Centralized Forwarding Card WS-F6700-CFC SAL1209HMM8 4.0 Ok

6 Policy Feature Card 3 WS-F6K-PFC3B SAL0943407P 2.1 Ok

6 MSFC3 Daughterboard WS-SUP720 SAL094659X8 2.3 Ok

any help is appreciated.

2 REPLIES
Blue

Re: SUP720 error

Hi:

What makes you think that upgrading the IOS will solve the problem?

To me, it sounds like you are experiencing a hardware failure on your [EDIT] SUP module's [EDIT] ASIC chips. The firmware that detected it was probably a hardware test, like a POST, except it runs regularly during operation.

I would look into reseating the card in the chassis to reset it or possibly replace it, especially if this error keeps coming up.

Lastly, if this was an IOS issue, I doubt it would only effect one module that way it has.

HTH

Victor

New Member

Re: SUP720 error

I am only basing it on the return message from the Error message debugger and the fact that I am not experience any such error on my second 6509 running a later firmware.

307
Views
0
Helpful
2
Replies
CreatePlease login to create content