Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Switch c2950 ios command support

We r having c2950 switch and we want

to use mac address group command.

We have put ios c2950-i6q4l2-tar.121-22.EA13.bin.Still not getting mac access-group command.

Can any body help?

Vaishali

6 REPLIES
Cisco Employee

Re: Switch c2950 ios command support

Hi,

This feature is available only on 2950 models which support the EI images:

Here are the EI models:

1. WS-C2950G-12-EI

2. WS-C2950G-24-EI

3. WS-C2950G-48-EI

4. WS-C2950G-24-EI-DC

5. WS-C2950T-24

6. WS-C2950C-24

Here are the SI models:

1. WS-C2950SX-48-SI

2. WS-C2950T-48-SI

3. WS-C2950SX-24

4. WS-C2950-24

5. WS-C2950-12

HTH

Laurent.

Hall of Fame Super Gold

Re: Switch c2950 ios command support

c2950-i6q4l2-tar.121-22.EA13.bin??? Are you sure this is the correct filename?

New Member

Re: Switch c2950 ios command support

Sorry

I made a mistake.

I just want to know if right now my c2950 is having standard image is it possible to change it to enhanced image

Correct file name is c2950-i6q4l2-mz.121-22.EA13.bin

Thanks

Re: Switch c2950 ios command support

Hi Vaishali,

On 2950 platform the switch model decides whether it's an SI switch or EI switch.

You can't upgrade from SI switch to EI switch.

Here's what the Q&A states -

Q. What is the difference between the Cisco Standard Image software and Cisco Enhanced Image software?

A. These two software image versions support different degrees of capability. The version of software depends solely on the model of switch selected, with no upgrade capabilities.

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps628/prod_qas09186a008009258e.html

If you can let us know the switch model number or paste show version out put we can find which switch you have.

-> Sushil

Re: Switch c2950 ios command support

Hi Leo,

The file name looks fine apart from the fact that in the end it should be .tar instead of .bin if you are searching for this IOS in the download area. For some strange reason Feature Navigator is not able to search for this IOS.

Vaishali, as pointed out by Laurent (+5 pts), this feature is supported on the switches with Enhanced Image. Based on the list provided by Laurent you can figure out if the switch you have is SI or EI switch.

Unfortunately 2950 SI switches can not be upgraded to EI switches. So if you have one of the SI switches then you won't be able to have MAC ACLs supported on it.

-> Sushil

Hall of Fame Super Gold

Re: Switch c2950 ios command support

Hi Vaishali,

"I just want to know if right now my c2950 is having standard image is it possible to change it to enhanced image"

Do a "sh version" and look at below:

cisco WS-C2950SX-24 (RC32300) processor (revision L0) with 19912K bytes of memory.

Processor board ID XXXXXXXXXXX

Last reset from system-reset

Running Standard Image <<<<<<<<<<<<

24 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

Standard Image or Enhanced Image is based on your appliance.

350
Views
10
Helpful
6
Replies
CreatePlease login to create content