Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Switch time and date

Hi all,

Can any one tell me how to set the time and date on 3560 switches.

Best Regards,

Ayman Yehia

2 ACCEPTED SOLUTIONS

Accepted Solutions
Hall of Fame Super Blue

Re: Switch time and date

207558867 wrote:

Hi all,

Can any one tell me how to set the time and date on 3560 switches.

Best Regards,

Ayman Yehia

Ayman

See this config guide for details -

http://www.cisco.com/en/US/docs/switches/lan/catalyst3560/software/release/12.2_44_se/configuration/guide/swadmin.html#wp1020905

Note though if you do it manually as above then when the system is restarted you need to reset the time again. This is because the 3560 does not have a hardware clock. Therefore NTP is a much better way to keep the time synchronised on your network devices that don't have hardware clocks -

3560 NTP config

Jon

Re: Switch time and date

Hi all,

Can any one tell me how to set the time and date on 3560 switches.

Best Regards,

Ayman Yehia

Hi Ayman,

The heart of the time service is the system clock. This clock runs from the moment the system starts up and keeps track of the date and time.The time remains accurate until the next system restart. As per the  recommendation says  use manual configuration only as a last resort. If you have an outside source to which the switch can synchronize (NTP), you do not need to manually set the system clock.

Following is the command to set clock manually on switches :-

Switch# clock set 13:32:00 23 July 2001

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

5 REPLIES
Hall of Fame Super Blue

Re: Switch time and date

207558867 wrote:

Hi all,

Can any one tell me how to set the time and date on 3560 switches.

Best Regards,

Ayman Yehia

Ayman

See this config guide for details -

http://www.cisco.com/en/US/docs/switches/lan/catalyst3560/software/release/12.2_44_se/configuration/guide/swadmin.html#wp1020905

Note though if you do it manually as above then when the system is restarted you need to reset the time again. This is because the 3560 does not have a hardware clock. Therefore NTP is a much better way to keep the time synchronised on your network devices that don't have hardware clocks -

3560 NTP config

Jon

Re: Switch time and date

Hi all,

Can any one tell me how to set the time and date on 3560 switches.

Best Regards,

Ayman Yehia

Hi Ayman,

The heart of the time service is the system clock. This clock runs from the moment the system starts up and keeps track of the date and time.The time remains accurate until the next system restart. As per the  recommendation says  use manual configuration only as a last resort. If you have an outside source to which the switch can synchronize (NTP), you do not need to manually set the system clock.

Following is the command to set clock manually on switches :-

Switch# clock set 13:32:00 23 July 2001

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

New Member

Re: Switch time and date

Thanks for your update

but can i now make the one of my core switches 6513 work as NTP server .??

and if it is possible does it affect the performance of the core or not ??

Thanks

Ayman Yehia

Hall of Fame Super Gold

Re: Switch time and date

If your core switch is synchronized then yes it's a good idea.  You don't need to configure the core switch just configure the switch with the command "ntp server [prefer]".

Re: Switch time and date

Thanks for your update

but can i now make the one of my core switches 6513 work as NTP server .??

and if it is possible does it affect the performance of the core or not ??

Thanks

Ayman Yehia

Hi Ayman,

Following is the command to make the switch as ntp server for clients in your network and it wont affect any performance issue with 6500 series if it is configured as NTP server for clients.

HG1#clock set 00:00:00 1 Jan 2000
HG1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
HG1(config)#ntp master 3

and at the clients end configure as

ntp server 10.x.x.x prefer (NTP servers if there are more)  ip address of the core switch which is reachble from network and ntp port needs to be opened that is 123.

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

32839
Views
0
Helpful
5
Replies
CreatePlease login to create content