Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Syslog Message: %SIP-3-UNSUPPORTED: Unsupported ptime value

Receiving syslog message :%SIP-3-UNSUPPORTED: Unsupported ptime value.  But we have no SIP-related commands in our config. We reloaded router Friday eve 1/15 but two more %SIP-3-UNSUPPORTED: Unsupported ptime value messages re-appeared on 1/18. The router in question is a 3745 running c3745-a3jk9s-mz.123-14.t7.bin. This router does have one interface facing an ISP. Any suggestions?  Thanks.

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: Syslog Message: %SIP-3-UNSUPPORTED: Unsupported ptime value

Hi,

SIP is enabled by default so if you don't need it, you can use the following command to stop this service:

sip-ua
 no transport udp
 no transport tcp
 no transport tcp tls


To check if SIP is enabled, you can use the following commands:

Router#show processes | include SIP
     149 Mwe 40F48254            4          1    400023108/24000  0 CCSIP_UDP_SOCKET
     150 Mwe 40F48034            4          1    400023388/24000  0 CCSIP_TCP_SOCKET

or

router#sh ip sockets
Proto    Remote      Port      Local       Port  In Out Stat TTY OutputIF
 17 0.0.0.0             0 10.16.60.5       5060   0   0  211   0 
 17 10.1.57.53        514 10.16.60.5      58917   0   0   10   0 
 17 10.1.57.55         49 10.16.60.5         49   0   0   11   0 
 17 10.1.57.56         49 10.16.60.5         49   0   0   11   0 
 17 0.0.0.0             0 10.16.60.5       2517   0   0    1   0 
 17 10.1.74.49       1757 10.16.60.5        161   0   0    1   0 

HTH

Laurent.

5 REPLIES
Cisco Employee

Re: Syslog Message: %SIP-3-UNSUPPORTED: Unsupported ptime value

Hi,

SIP is enabled by default so if you don't need it, you can use the following command to stop this service:

sip-ua
 no transport udp
 no transport tcp
 no transport tcp tls


To check if SIP is enabled, you can use the following commands:

Router#show processes | include SIP
     149 Mwe 40F48254            4          1    400023108/24000  0 CCSIP_UDP_SOCKET
     150 Mwe 40F48034            4          1    400023388/24000  0 CCSIP_TCP_SOCKET

or

router#sh ip sockets
Proto    Remote      Port      Local       Port  In Out Stat TTY OutputIF
 17 0.0.0.0             0 10.16.60.5       5060   0   0  211   0 
 17 10.1.57.53        514 10.16.60.5      58917   0   0   10   0 
 17 10.1.57.55         49 10.16.60.5         49   0   0   11   0 
 17 10.1.57.56         49 10.16.60.5         49   0   0   11   0 
 17 0.0.0.0             0 10.16.60.5       2517   0   0    1   0 
 17 10.1.74.49       1757 10.16.60.5        161   0   0    1   0 

HTH

Laurent.

New Member

Re: Syslog Message: %SIP-3-UNSUPPORTED: Unsupported ptime value

Genius!  Thank you very much.

New Member

Syslog Message: %SIP-3-UNSUPPORTED: Unsupported ptime value

Seems to have solved my problem too! Thanks!

*Jun 30 18:13:57: %SIP-3-UNSUPPORTED: Unsupported ptime value

*Jun 30 18:17:05: %SIP-3-UNSUPPORTED: Unsupported ptime value

*Jun 30 18:20:17: %SIP-3-UNSUPPORTED: Unsupported ptime value

*Jun 30 18:23:23: %SIP-3-UNSUPPORTED: Unsupported ptime value

*Jun 30 18:26:28: %SIP-3-UNSUPPORTED: Unsupported ptime value

*Jun 30 18:29:39: %SIP-3-UNSUPPORTED: Unsupported ptime value

*Jun 30 18:32:51: %SIP-3-UNSUPPORTED: Unsupported ptime value

*Jun 30 18:35:53: %SIP-3-UNSUPPORTED: Unsupported ptime value

*Jun 30 18:38:10: %SYS-5-CONFIG_I: Configured from console by srand on vty0 (10.3.12.100)

#               show clock

*18:41:00.851 aest Thu Jun 30 2011

It was occurring every three minutes, but no longer!

-Steve

New Member

Syslog Message: %SIP-3-UNSUPPORTED: Unsupported ptime value

Hello All,

i have same issue, actually my router is on Edge, and is acting as pass through for VOIP / SIP calls from my asterisk server to Internet base VOIP provider.

soo if i disable this service on router, will it casue pass through to stop working as well? any thoughts?

New Member

Syslog Message: %SIP-3-UNSUPPORTED: Unsupported ptime value

I am having the same issue, but I am actually using CME as SIP, and that message is really annoying. Not to mention that when the customer sees it, he's gonna ask me what that is and I have no clue what to answer. I already looked it up, but all I can find is this post and things that don't explain about this error.

All I need to do is stop the message from showing. Any ideas?

11104
Views
20
Helpful
5
Replies