Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

TFTP: error code 1 received - 18025

hi all,

i got a strange error on a 3750. i just do a:

copy running-config startup-config

here is the output:

Destination filename [startup-config]?

Building configuration...

[OK]

TFTP: error code 1 received - 18025

here is the version:

Cisco IOS Software, C3750 Software (C3750-IPBASEK9-M), Version 12.2(46)SE, RELEASE SOFTWARE (fc2)

here is the memory information:

Directory of flash:/

2 -rwx 9204473 Mar 1 1993 01:09:42 +01:00 c3750-ipbasek9-mz.122-46.SE.bin

3 -rwx 17872 Mar 1 1993 01:25:06 +01:00 startup-config1

4 -rwx 4120 Oct 27 2009 12:19:36 +01:00 multiple-fs

5 -rwx 736 Mar 1 1993 01:00:33 +01:00 vlan.dat

6 -rwx 9082 Oct 27 2009 12:19:36 +01:00 private-config.text

8 -rwx 18591 Oct 27 2009 12:19:36 +01:00 config.text

15998976 bytes total (6741504 bytes free)

Directory of system:/

2 -r-- 0 <no date> default-running-config

4 dr-x 0 <no date> memory

1 -rw- 19926 <no date> running-config

3 dr-x 0 <no date> vfiles

No space information available

Directory of tmpsys:/

No files in directory

No space information available

Directory of nvram:/

484 -rw- 18591 <no date> startup-config

485 ---- 9082 <no date> private-config

1 -rw- 1736 <no date> ifIndex-table

2 -rw- 579 <no date> IOS-Self-Sig#3232.cer

4 ---- 12 <no date> persistent-data

524288 bytes total (492467 bytes free)

so where's the problem ?

regards Reinhold

6 REPLIES

Re: TFTP: error code 1 received - 18025

Could you please post the output from:

sh run | inc tftp

regards,

Leo

Community Member

Re: TFTP: error code 1 received - 18025

hi Leo,

thanks for answer.

the output is empty.

regards Reinhold

VIP Super Bronze

Re: TFTP: error code 1 received - 18025

Reinhold,

You normally get this error when you are pointing to a miss configured TFTP server.

Just curious, does “wr” gives you the same results?

HTH

Reza

Community Member

Re: TFTP: error code 1 received - 18025

hi Reza,

yes, the output is the same. when i tftp to my server it works without problems.

wr

Building configuration...

[OK]

TFTP: error code 1 received - 18025

switch#copy run tftp:

Address or name of remote host []? ip

Destination filename [switch-confg]?

!!

19926 bytes copied in 1.199 secs (16619 bytes/sec)

thanks, Reinhold

Re: TFTP: error code 1 received - 18025

Perhaps your flash is corrupted or set to write only.

Please check the contents of the config-register

I also noticed that you installed an image via a direct copy from tftp to flash, otherwise the .bin would be in sub-folder.

I would recommend to erase the flash, format it and reinstall it using the archive command:

http://www.cisco.com/en/US/products/hw/switches/ps5023/products_configuration_example09186a00804799d7.shtml

regards,

Leo

Community Member

Re: TFTP: error code 1 received - 18025

hi Leo,

Configuration register is 0xF

i changed a little bit in the config and downloaded it to my server and it was the changed one. so the flash should be ok. don't you think ?

regards Reinhold

8399
Views
0
Helpful
6
Replies
CreatePlease to create content