1.- SM-ES2-24-P: EtherSwitch SM L2 + PoE + 23 10/100 + 1 10/100/1000 on Slot 1
2.- CISCO2911/K9 chassis
a) when I try tolog in via telnetto the devicedoes not respond, butif I senda pingthisrespondssmoothly
b) The problem is thatwhen I seethe device restarts
when ocurrs the reboot on the device always sent this log:
Oct 29 14:23:47.251: %SYS-5-CONFIG_I: Configured from memory by console Oct 29 14:23:47.527: %LINEPROTO-5-UPDOWN: Line protocol on Interface EDSP0, changed state to up Oct 29 14:23:47.875: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request Oct 29 14:23:49.451: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state to up Oct 29 14:23:49.515: %ILPM_FAULT-5-ILPM_NOTICE: Notice: Inline power supply is being started. Oct 29 14:23:49.515: %ILPM_FAULT-5-ILPM_WARNING: Warning: Ethernet Switch Network Modules with PoE Support need to be reloaded to function properly. Oct 29 14:23:50.451: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up Oct 29 14:23:51.063: %SYS-5-RESTART: System restarted -- Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M1, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2011 by Cisco Systems, Inc. Compiled Tue 14-Jun-11 19:25 by prod_rel_team Oct 29 14:23:51.067: %SNMP-5-COLDSTART: SNMP agent on host client is undergoing a cold start
this warning message is not a indication of any ERROR in the system but a WARNING upon system reload or PoE power supply restoration. This is a new PoE power supply OIR feature. Upon PoE OIR, inline power supply restores automatically in the router but Ether Switch Network module requires to be reloaded for PoE supply to work properly in the Ethernet switch .
As Insharie noted, the posted messages have nothing to do with the inability to telnet to the device. Are you trying and failing to telnet to the router or the etherswitch? What configuration, if any, do you have on the vty lines of the device?
I have same problem but the ip phones connect in sw module is not working becouse absent of POE.
I have already reload the module and the gateway nothing work.
ACMEGW_GW01#show power inline PowerSupply SlotNum. Maximum Allocated Status ----------- -------- ------- --------- ------ INT-PS 0 280.000 0.000 PS GOOD RPS ABSENT Interface Config Device Powered PowerAllocated --------- ------ ------ ------- -------------- Gi1/0 auto Unknown Off 0.000 Watts
Ethernet Switch Network Modules with PoE support should be reloaded to function properly upon PoE Power Supply OIR insertion/removal.
*Nov 18 14:25:38.207 GMT-2: %ILPM_FAULT-5-ILPM_NOTICE: Notice: Inline power supp ly is being started. *Nov 18 14:25:38.207 GMT-2: %ILPM_FAULT-5-ILPM_WARNING: Warning: Ethernet Switch Network Modules with PoE Support need to be reloaded to function properly. *Nov 18 14:25:40.035 GMT-2: %SYS-5-RESTART: System restarted -- Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.4(3)M4, REL EASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2015 by Cisco Systems, Inc. Compiled Sun 27-Sep-15 06:34 by prod_rel_team
This document gives several answers on frequently asked questions for PFRv3 channel state behavior.
Q1: What are all the channel operational states from a BR (border role) perspective and what are the rules/conditions to be in each st...
The need was to reach an host inside a LAN through a VPN connection managed by the LAN gateway (Cisco 1921).
The LAN gateway performs NAT and there was a dedicate nat rule for the host i wanted to reach through VPN.
I couldn't connect to the hos...
We have 3 identical switches configured by someone else and would like to claim some of the Gigabit ports(G1/G2/G3/G4) for use on servers. When we try to change the wiring and configuration, we run in to connectivity issues. Attached is a des...