Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Trunk speed between 6509 and nx7000

I have connected a 2 TP trunk between 6509 and nx 7000, as shown above. I am trying to have speed 1000 on both sides.

If I set speed 1000  on 6509 Trunk disconnect

Does anybod know how to force speed 1000 ?

6509#sh int g 4/12 status

Port    Name               Status       Vlan       Duplex  Speed Type

Gi4/12  *** Porta 4/12 - T connected    trunk       a-full  a-100 10/100/1000BaseT

6509i#sh int g 4/13 status

Port    Name               Status       Vlan       Duplex  Speed Type

Gi4/13  *** Porta 4/13 - T connected    trunk       a-full  a-100 10/100/1000BaseT

NX7000# sh interface eth 10/47 status

--------------------------------------------------------------------------------

Port          Name               Status    Vlan      Duplex  Speed   Type

--------------------------------------------------------------------------------

Eth10/47      *** Trunk com 6509 connected trunk     full    100     10/100/1000

NX7000# sh interface eth 10/48 status

--------------------------------------------------------------------------------

Port          Name               Status    Vlan      Duplex  Speed   Type

--------------------------------------------------------------------------------

Eth10/48      *** Trunk com 6509 connected trunk     full    100     10/100/1000

NX7000#

1 ACCEPTED SOLUTION

Accepted Solutions
Purple

Re: Trunk speed between 6509 and nx7000

  Set both sides as auto and it should negotiate 1000  without having to force a speed .  Auto is the general recomendation when using gigabit ethernet. The nexus side looks like it is hardcoded to 100/full thats why it will go down if you try to hardcode the 6500 side to 1000 .

4 REPLIES
Purple

Re: Trunk speed between 6509 and nx7000

  Set both sides as auto and it should negotiate 1000  without having to force a speed .  Auto is the general recomendation when using gigabit ethernet. The nexus side looks like it is hardcoded to 100/full thats why it will go down if you try to hardcode the 6500 side to 1000 .

New Member

Trunk speed between 6509 and nx7000

Thanks.

I know how to set 6509 auto comand but I do not, on 7000.

Could you please help me ?

Rosa

New Member

Trunk speed between 6509 and nx7000

I have executed on NX7000:

port-channel and both eth interfaces

shut

speed auto

noshut

NX7000# sh int  eth 10/48 status

--------------------------------------------------------------------------------

Port          Name               Status    Vlan      Duplex  Speed   Type

--------------------------------------------------------------------------------

Eth10/48      *** Trunk com 6509 notconnec trunk     full    auto    10/100/1000

NX7000# sh int  eth 10/47 status

--------------------------------------------------------------------------------

Port          Name               Status    Vlan      Duplex  Speed   Type

--------------------------------------------------------------------------------

Eth10/47      *** Trunk com 6509 connected trunk     full    1000    10/100/1000

NX7000# sh int port-channel 99 status

--------------------------------------------------------------------------------

Port          Name               Status    Vlan      Duplex  Speed   Type

--------------------------------------------------------------------------------

Po99          *** TRUNK WC1 (TP) connected trunk     full    1000    --        

I have executed on 6509:

port-channel and both eth interfaces

shut

speed auto

noshut

6509#sh int g 4/12 status        

Port    Name               Status       Vlan       Duplex  Speed Type

Gi4/12  *** Porta 4/12 - T connected    trunk       a-full a-1000 10/100/1000BaseT

6509#sh int g 4/13 status

Port    Name               Status       Vlan       Duplex  Speed Type

Gi4/13  *** Porta 4/13 - T notconnect   1           a-full  a-100 10/100/1000BaseT

6509#sh int port-channel 99 status

Port    Name               Status       Vlan       Duplex  Speed Type

Po99    *** Port-Channel 9 connected    trunk       a-full a-1000

New Member

Trunk speed between 6509 and nx7000

It is fine. all boxes - speed 1000

393
Views
0
Helpful
4
Replies