Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Trunking over Ethernet.

Am I able to trunk from a switch to a router if my router does not have Fast Ethernet -

The router I am using only has an Ethernet port -

Joe

  • LAN Switching and Routing
1 ACCEPTED SOLUTION

Accepted Solutions

Re: Trunking over Ethernet.

Joseph,

There's a Cisco tool called Cisco Feature Navigator.
It shows which features can be done for each image among other things.

802.1q is not supported on your current IOS.

Federico.

13 REPLIES

Re: Trunking over Ethernet.

Hi Joseph,

Are you using a switch that only supports (or is only configured) for 10Mbps?

Federico.

New Member

Re: Trunking over Ethernet.

I am using a 2950.

Re: Trunking over Ethernet.

Ok but the interface of the 2950 that you're connecting to the router is not hard-coded to 10Mbps?

If you change the configuration from trunk to access on the switch (disable trunking on the router side), does it work?

I just want to see if the problem is with the trunking (don't think so), or the problem is there' s no connectivity at all between the switch and the router).

Federico.

New Member

Re: Trunking over Ethernet.

Federico

I'll tell you what I am doing so you have a better understanding.

I am hooking up a switch to a router so I can incorporate inter-vlan routing.

I have a switch with 10/100 ports and I have a router that only has 10base-T interface card.

I want to create a trunk between the router and the switch so that I can inter-vlan.

When I go to assign the IP address on the router sub-interface it tells me:

'Configuring IP routing on a LAN subinterface is only allowed if that subinterface is already configured as part of an IEEE 802.10, IEEE 802.1Q, or ISL vLAN."

Hall of Fame Super Blue

Re: Trunking over Ethernet.

joealbergo wrote:

F

When I go to assign the IP address on the router sub-interface it tells me:

'Configuring IP routing on a LAN subinterface is only allowed if that subinterface is already configured as part of an IEEE 802.10, IEEE 802.1Q, or ISL vLAN."

Joe

You need to enter the encapsulation before you can enter an IP ie.

int fa0/1.10

encapsulation dot1q 10

ip address 192.168.5.1 255.255.255.0

Jon

Re: Trunking over Ethernet.

Before assigning the IP on the sub-interface, you need the command:  encapsulation dot1q xx  --> xx is the number of the VLAN

Otherwise you can't configure an IP address.

Federico.

Hall of Fame Super Blue

Re: Trunking over Ethernet.

Joe

You can trunk on 10mbps interfaces but support for this was brought in later than with 100Mbps interfaces. Also you need the correct feature set to support 802.1q trunking.

So what is the router you are using and what is the feature set -  a "sh version" will give this info.

Jon

New Member

Re: Trunking over Ethernet.

Router#sh version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.0(5)XK1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC:Home:SW:IOS:Specials for info
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 14-Sep-99 15:53 by jjgreen
Image text-base: 0x80008088, data-base: 0x8073CEEC

ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-I-M), Version 12.0(5)XK1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

Router uptime is 1 hour, 13 minutes
System returned to ROM by power-on at 12:59:03 UTC Sat Feb 6 2010
System image file is "flash:c2600-i-mz.120-5.XK1"

cisco 2610 (MPC860) processor (revision 0x202) with 22528K/2048K bytes of memory.
Processor board ID JAB03200221 (2019881742)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2142

Hall of Fame Super Blue

Re: Trunking over Ethernet.

Joe

You will need at least 12.2(2)T for 802.1q support on the 10BaseT interface of your 2600 router -

802.1q support 2600

Jon

717
Views
28
Helpful
13
Replies