Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Vlan Help

Good afternoon,

Below is a copy of the switch VLan information I've erased the Vlan.dat file from flash, when i reboot the switch and run the show vlan

I can still see the following, how can i delete these entries

2    vlanTraining                     active

3    vlanTraining2                    active

Switch#show vlan

VLAN Name                             Status    Ports

---- -------------------------------- --------- -------------------------------

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4,

                                                Fa0/5, Fa0/6, Fa0/7, Fa0/8,

                                                Fa0/9, Fa0/10, Fa0/11, Fa0/12,

                                                Fa0/13, Fa0/14, Fa0/15, Fa0/16,

                                                Fa0/17, Fa0/18, Fa0/19, Fa0/20,

                                                Fa0/21, Fa0/22, Fa0/23, Fa0/24,

                                                Fa0/25, Fa0/26, Fa0/27, Fa0/28,

                                                Fa0/29, Fa0/30, Fa0/31, Fa0/32,

                                                Fa0/33, Fa0/34, Fa0/35, Fa0/36,

                                                Fa0/37, Fa0/38, Fa0/39, Fa0/40,

                                                Fa0/41, Fa0/42, Fa0/43, Fa0/44,

                                                Fa0/45, Fa0/46, Fa0/47, Fa0/48,

                                                Gi0/1, Gi0/2

2    vlanTraining                     active

3    vlanTraining2                    active

1002 fddi-default                     active

1003 trcrf-default                    active

1004 fddinet-default                  active

1005 trbrf-default                    active

VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2

---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------

1    enet  100001     1500  -      -      -        -    -        0      0

2    enet  100002     1500  -      -      -        -    -        0      0

3    enet  100003     1500  -      -      -        -    -        0      0

1002 fddi  101002     1500  -      -      -        -    -        0      0

1003 trcrf 101003     4472  1005   3276   -        -    srb      0      0

1004 fdnet 101004     1500  -      -      -        ieee -        0      0

1005 trbrf 101005     4472  -      -      15       ibm  -        0      0

VLAN AREHops STEHops Backup CRF

---- ------- ------- ----------

1003 7       7       off

Switch#

Regards

Paul

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
VIP Purple

Vlan Help

HI

try to use this command ...

Switch(config)# no vlan X

and the show the ouput with sh vlan command:

Regards

Please rate if it helps.

2 REPLIES
VIP Purple

Vlan Help

HI

try to use this command ...

Switch(config)# no vlan X

and the show the ouput with sh vlan command:

Regards

Please rate if it helps.

New Member

Re: Vlan Help

HI Sandeep,

Thank you for your support i've accessed  the Vlan database and run the command you gave above,

fantastic it's worked a treat and remove the vlan name.

thanks

Paul

133
Views
0
Helpful
2
Replies