Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

VLAN on 3com 2952 and Cisco 3750

HI,

Pls help.

I have setup both Vlans on 3com and cisco. but it seems they cant talk to each other.

ive setup both on trunking mode, what supposed to be the solution on this?

thank in advance

Everyone's tags (4)
1 ACCEPTED SOLUTION

Accepted Solutions
VIP Super Bronze

VLAN on 3com 2952 and Cisco 3750

So, the 3com switch is layer-2 only and the 3750 is layer-2 and 3?

I am not familiar with 3com config, but it appears that you have only enabled vlan 1 on the trunk port connecting to the 3750.  Can you also add vlan 3 and test again?

Is the vlan interface on the 3750 in up and up mode?

sh ip int bri vlan3

is interface gi1/0/1 in up and up mode

sh ip int bri gi1/0/1

how about the 3com interfaces?

HTH

6 REPLIES
VIP Super Bronze

VLAN on 3com 2952 and Cisco 3750

What is the topology look like?

How are the switches connected?

Can you provide "sh run" from the 3750?

New Member

Re: VLAN on 3com 2952 and Cisco 3750

Topology is

Cisco 3750       connected to        3com

g1/0/1                   -----------          g1/0/1

I created VLAN 3 for each switch.

here is the SH RUN

#####

Cisco 3750

ip routing

interface GigabitEthernet1/0/1

switchport trunk encapsulation dot1q

switchport mode trunk

switchport nonegotiate

interface GigabitEthernet1/0/2

switchport access vlan 3

spanning-tree portfast

interface Vlan3

ip address 10.3.0.1 255.255.0.0

ip route 0.0.0.0 0.0.0.0 10.0.0.137

3com 2952 Baseline

#

vlan 1

#

vlan 3

#

#

ip route-static 0.0.0.0 0.0.0.0 10.0.0.2

#

interface GigabitEthernet1/0/1

port link-type trunk

port trunk permit vlan 1

stp edged-port enable

#

interface GigabitEthernet1/0/2

port access vlan 3

stp edged-port enable

Did i miss something? thank pls help

VIP Super Bronze

VLAN on 3com 2952 and Cisco 3750

So, the 3com switch is layer-2 only and the 3750 is layer-2 and 3?

I am not familiar with 3com config, but it appears that you have only enabled vlan 1 on the trunk port connecting to the 3750.  Can you also add vlan 3 and test again?

Is the vlan interface on the 3750 in up and up mode?

sh ip int bri vlan3

is interface gi1/0/1 in up and up mode

sh ip int bri gi1/0/1

how about the 3com interfaces?

HTH

New Member

Re: VLAN on 3com 2952 and Cisco 3750

yup they are all up.. same as 3com switch.

The 3com switch uses web gui, it seems by default vlan1 is enabled on int g1/0/1.. let me try if I could add to permit vlan 3..

New Member

Re: VLAN on 3com 2952 and Cisco 3750

@Reza..

nice one that do the trick..

i just put the

port trunk permit vlan 1 to 3

then i can ping vlans on 3750..

VIP Super Bronze

VLAN on 3com 2952 and Cisco 3750

Glad to help, and thanks for the rating

Good Luck Mark

Reza

2890
Views
0
Helpful
6
Replies
CreatePlease login to create content