Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Vlan (tagged)issue on a cisco ap aironet 1250 and switch hp 1905

Hello everyone,

I have configured my switch using vlan 1 and 2, on ports 1-2 and 7-8 respectively. I have not mode trunk on this switch so i use hybrid port:

SwitchHP(configure)# interface ethernet 1/1

SwitchHP(configure-if)# switchport mode hybrid

SwitchHP(configure-if)# switchport allowed vlan add 1 untagged

SwitchHP(configure-if)# interface ethernet 1/2

SwitchHP(configure-if)# switchport allowed vlan add 1 untagged

SwitchHP(configure)# interface ethernet 1/7

SwitchHP(configure-if)# switchport mode hybrid

SwitchHP(configure-if)# switchport allowed vlan add 2 untagged

SwitchHP(configure-if)# switchport allowed vlan remove 1

SwitchHP(configure-if)# switchport native vlan 2

SwitchHP(configure)# interface ethernet 1/8

SwitchHP(configure-if)# switchport mode hybrid

SwitchHP(configure-if)# switchport allowed vlan add 2 untagged

SwitchHP(configure-if)# switchport allowed vlan remove 1

SwitchHP(configure-if)# switchport native vlan 2

I have to configure untagged mode on my ports because they are connected directly to a computers on mode access.

Using above configuration everything is working fine.

My problem begin when I try to connect my AP on mode trunk, because it use 2 vlans with different SSIDs, and vlan 1 like native; So, I think aironet tag vlan 2, hence i have to configure my switch port like that:

Port 1/5 from switch on mode hybrid connected by ethernet to aironet sub-interfaces 0.1 and 0.2:

SwitchHP(configure)# interface ethernet 1/5

SwitchHP(configure-if)# switchport allowed vlan add 2 tagged

SwitchHP(configure-if)# switchport allowed vlan add 1 untagged

SwitchHP(configure-if)# switchport native vlan 1

That is not working fine because tagged traffic from aironet is dropped for my switch, how can i solve it?

I think I can't configure vlan 2 using tag on my switch because there is a computer connected on that port and its traffic is not tagged...

AP is well configured because i have it configured like that at other location.

Thank you for your time.

Regards, Jesus.

8 REPLIES

Vlan (tagged)issue on a cisco ap aironet 1250 and switch hp 1905

is there any way to tag an access port on a switch?

New Member

Re: Vlan (tagged)issue on a cisco ap aironet 1250 and switch hp

hi there

I think AP talks to controller over wireless using LWAPP protocol, not sure about HP though. So on the switch I think all it needs is the connectivity for DHCP options.

Sent from Cisco Technical Support iPhone App

Vlan (tagged)issue on a cisco ap aironet 1250 and switch hp 1905

Hi naresh, thank you for your quick answer.

I don't understand very well what you're talking about, because i think my problem is about tagging options on a switch, not about dhcp protocol...

Could you explain me something more about that?

Regards

New Member

Re: Vlan (tagged)issue on a cisco ap aironet 1250 and switch hp

From what I understand SSIDs etc communicate with controller over wireless. As far as switch is concerned, APs receive DHCP options from controller for connectivity, so I think that switch ports can just be access ports.

Sent from Cisco Technical Support iPhone App

Bronze

Re: Vlan (tagged)issue on a cisco ap aironet 1250 and switch hp

Vlan (tagged)issue on a cisco ap aironet 1250 and switch hp 1905

thank you, but it wasn't helpful.

Vlan (tagged)issue on a cisco ap aironet 1250 and switch hp 1905

I found that:

http://www.devrandom.za.net/2010/04/routing-between-vlans-cisco-router-and.html

but i think my configuration is very similar, doesn't it? Why is it not working? Looking for that on google, I found too much threads about connection issues between router on a stick connected to switch 3com (hp).. :s but anything helpful...

Bronze

Re: Vlan (tagged)issue on a cisco ap aironet 1250 and switch hp

Hi Jesus,

The router-on-a-stick concept has been developed by Cisco. I don't know if it will work with third party equipment like HP.

Eugen

1752
Views
0
Helpful
8
Replies