Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

VMPS reconfirms a lot of times

Hello,

Can someone explain why VMPS reconfirms more than configured ?

03:26:59: %VQPCLIENT-7-RECONF: Reconfirming VMPS responses

03:26:59: VQPC: Set needReconfirm. Total ReconfirmPending:1

03:26:59: VQPC PAK: xmt transaction ID = 0x00000019

03:26:59: VQPC PAK: sending query to VMPS

03:26:59: VQPC: Started throttle timer, Pkt Sent:1, Pending:0

03:26:59: VQPC PAK:

03:26:59: VQPC PAK: rcvd packet from VMPS

03:26:59: VQPC PAK: transaction ID = 0x00000019

03:26:59: VQPC: rcvd response, transID = 0x00000019

03:26:59: VQPC PAK: VLAN name TLV, vlanName = default

03:26:59: VQPC PAK: Cookie TLV, cookie = 000b.cde3.855f, length = 6

03:27:00: VQPC: Finished Reconfirmation

03:27:00: VQPC: Starting reconfirm timer again!

03:27:45: VQPC PAK: xmt transaction ID = 0x0000001A

03:27:45: VQPC PAK: sending query to VMPS

03:27:45: VQPC PAK:

03:27:45: VQPC PAK: rcvd packet from VMPS

03:27:45: VQPC PAK: transaction ID = 0x0000001A

03:27:45: VQPC: rcvd response, transID = 0x0000001A

03:27:45: VQPC PAK: VLAN name TLV, vlanName = default

03:27:45: VQPC PAK: Cookie TLV, cookie = 000b.cde3.855f, length = 6

03:38:56: VQPC PAK: xmt transaction ID = 0x0000001B

03:38:56: VQPC PAK: sending query to VMPS

03:38:56: VQPC PAK:

03:38:56: VQPC PAK: rcvd packet from VMPS

03:38:56: VQPC PAK: transaction ID = 0x0000001B

03:38:56: VQPC: rcvd response, transID = 0x0000001B

03:38:56: VQPC PAK: VLAN name TLV, vlanName = default

03:38:56: VQPC PAK: Cookie TLV, cookie = 000b.cde3.855f, length = 6

03:45:26: VQPC PAK: xmt transaction ID = 0x0000001C

03:45:26: VQPC PAK: sending query to VMPS

03:45:27: VQPC PAK:

03:45:27: VQPC PAK: rcvd packet from VMPS

03:45:27: VQPC PAK: transaction ID = 0x0000001C

03:45:27: VQPC: rcvd response, transID = 0x0000001C

03:45:27: VQPC PAK: VLAN name TLV, vlanName = default

03:45:27: VQPC PAK: Cookie TLV, cookie = 000b.cde3.855f, length = 6

NOTE: THE SWITCH IS CONNECTED TO ANOTHER SWITCH. WHEN IT RUNS 'stand alone', EVERYTHING SEEMS TO WORK. WHY ?

1 REPLY
New Member

Re: VMPS reconfirms a lot of times

I think reconfirm vmps command is use to reconfirm the current dynamic port VLAN membership with VMPS. VMPS clients periodically reconfirm the VLAN membership information received from the VMPS. For more information on VMPS please click following URL:

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/25ew/configuration/guide/vmps.html#wp29223

170
Views
0
Helpful
1
Replies