Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

what is controller T1 interface

Hi all,

i see this on router interface

Interface Status Protocol Description

Fa0/0 up up

Fa0/1 up up

Se2/0 up up

Se2/1 admin down down

Se3/0:0 up up

Lo0 up up

sh controller t1 3/0

T1 3/0 is up.

Applique type is Channelized T1

Cablelength is long gain36 0db

Description: Verizon T1 to Seligman Palo Alto

No alarms detected.

Framing is ESF, Line Code is B8ZS, Clock Source is Line.

Data in current interval (269 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 1:

10 Line Code Violations, 58 Path Code Violations

0 Slip Secs, 3 Fr Loss Secs, 4 Line Err Secs, 0 Degraded Mins

7 Errored Secs, 4 Bursty Err Secs, 3 Severely Err Secs, 75 Unavail Secs

Data in Interval 2:

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 9:

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 10:

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 10 15 minute intervals):

10 Line Code Violations, 58 Path Code Violations,

0 Slip Secs, 3 Fr Loss Secs, 4 Line Err Secs, 0 Degraded Mins,

7 Errored Secs, 4 Bursty Err Secs, 3 Severely Err Secs, 75 Unavail Secs

sh int Se3/0:0

Serial3/0:0 is up, line protocol is up

Hardware is PA-MC-8PRI

Internet address is 10.95.244.13/30

MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec,

reliability 255/255, txload 4/255, rxload 1/255

Encapsulation HDLC, crc 16, loopback not set

Keepalive set (10 sec)

Last input 00:00:03, output 00:00:00, output hang never

Last clearing of "show interface" counters 4w1d

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 40181

Queueing strategy: weighted fair

Output queue: 0/1000/64/40163 (size/max total/threshold/drops)

Conversations 0/16/16 (active/max active/max total)

Reserved Conversations 0/0 (allocated/max allocated)

5 minute input rate 5000 bits/sec, 6 packets/sec

5 minute output rate 27000 bits/sec, 6 packets/sec

49979303 packets input, 519290582 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 1 giants, 0 throttles

48593 input errors, 2711 CRC, 0 frame, 0 overrun, 0 ignored, 24252 abort

52430870 packets output, 4152546207 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

14 carrier transitions no alarm present

Timeslot(s) Used:1-24, subrate: 64Kb/s, transmit delay is 0 flags

can anyone explain we what is difference in serial3/0:0 interface and controller T1 3/0 interface?????????

or are they same interface???

3 REPLIES
New Member

Re: what is controller T1 interface

Hi,

the controller is the physical interface. A T1 has 24 channels.

The interface se3/0:0 is the first B-Channel out of 24.

Bye

Jo

New Member

Re: what is controller T1 interface

Hi jgross,

Thanks for reply.

so if we have se0 interface which is this

B-channel?

New Member

Re: what is controller T1 interface

Hello,

the controller defines the physical parameters, like framing and lincode, and D-channel Protocol, ... .

After you have specified the contoller you will find a corresponding serial interface in the configuration.

This is the D-Channel of the Interface used to exchange control information.

In Europe we have E1 Controllers, with 30 B-Channels to transfer data at 64kBit/s, and one D-Channel to exchange control information.

So there is not only one B-Channel.

E1 Interfaces have 30-B Channels, T1 have 24 B-Channels.

The D-Channel in Europe is in the middle, so it is numbered interface serial2/0:15.

The B-Channels are numbered starting from 0.

So the status of B-Channel 0 can be displayed with

show interface serial 2/0:0

B-Channel No 1 can be displayed with

show interface serial 2/0:1,

up to

show interface serial 2/0:23, for T1,

or

show interface serial 2/0:30, for E1

... .

Bye

Jo

394
Views
0
Helpful
3
Replies