cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
488
Views
0
Helpful
2
Replies

what means the following errors in debug ip packet output

ROMAN TOMASEK
Level 1
Level 1

Hi,

what means the following errors in debug ip packet output:

Mar 1 00:16:34.419: IP: s=0.0.0.0 (Vlan1), d=255.255.255.255, len 330, rcvd 2

*Mar 1 00:16:34.419: IP: s=0.0.0.0 (Vlan1), d=255.255.255.255, len 330, stop pr

ocess pak for forus packet

*Mar 1 00:16:34.419: IP: s=10.132.16.1 (local), d=10.132.1.16, len 330, local f

eature, Redirection Cli(6), rtype 0, forus FALSE, sendself FALSE, mtu 0

*Mar 1 00:16:34.419: IP: s=10.132.16.1 (local), d=10.132.1.16, len 330, local f

eature, Clustering(7), rtype 0, forus FALSE, sendself FALSE, mtu 0

*Mar 1 00:16:34.419: IP: tableid=0, s=10.132.16.1 (local), d=10.132.1.16 (Vlan1

0), routed via FIB

*Mar 1 00:16:34.419: IP: s=10.132.16.1 (local), d=10.132.1.16 (Vlan10), len 330

, sending

*Mar 1 00:16:34.419: IP: s=10.132.16.1 (local), d=10.132.1.16 (Vlan10), len 330

, output feature, Check hwidb(63), rtype 1, forus FALSE, sendself FALSE, mtu 0

*Mar 1 00:16:34.419: IP: s=10.132.16.1 (local), d=10.132.1.16 (Vlan10), len 330

, sending full packet

Thank you

Roman

1 Accepted Solution

Accepted Solutions

Giuseppe Larosa
Hall of Fame
Hall of Fame

Hello Roman,

I suppose you are using a multilayer switch.

I tried to look at command reference for debug ip packet in 12.2SX used in Cat6500.

I didn't find forus packet.

However, the first raw should be a DHCP request from a booting client if no ip helper-address pointing to a dhcp server is configured under vlan1 SVI the packet is discarded for its broadcast destination and this is correct behavior

the following lines are about a packet with source 10.132.16.1 with d= 10.132.1.16 and same size 330 byte as first discarded packet.

This packet is sent to 10.132.1.16.

I may be wrong but I think that you have ip helper-address under vlan1 pointing to ip 10.132.1.16 and that vlan1's ip address is 10.132.16.1

If so you are seeing the switch activity when receiving a dhcp request :

original packet is discarded

a modified version as per ip helper-address is routed to vlan10:

*Mar 1 00:16:34.419: IP: s=10.132.16.1 (local), d=10.132.1.16 (Vlan10), len 330

, sending full packet

Hope to help

Giuseppe

View solution in original post

2 Replies 2

Giuseppe Larosa
Hall of Fame
Hall of Fame

Hello Roman,

I suppose you are using a multilayer switch.

I tried to look at command reference for debug ip packet in 12.2SX used in Cat6500.

I didn't find forus packet.

However, the first raw should be a DHCP request from a booting client if no ip helper-address pointing to a dhcp server is configured under vlan1 SVI the packet is discarded for its broadcast destination and this is correct behavior

the following lines are about a packet with source 10.132.16.1 with d= 10.132.1.16 and same size 330 byte as first discarded packet.

This packet is sent to 10.132.1.16.

I may be wrong but I think that you have ip helper-address under vlan1 pointing to ip 10.132.1.16 and that vlan1's ip address is 10.132.16.1

If so you are seeing the switch activity when receiving a dhcp request :

original packet is discarded

a modified version as per ip helper-address is routed to vlan10:

*Mar 1 00:16:34.419: IP: s=10.132.16.1 (local), d=10.132.1.16 (Vlan10), len 330

, sending full packet

Hope to help

Giuseppe

Thank you for your explanation. It was help me. Roman

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card