cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
644
Views
7
Helpful
3
Replies

WIC-1B-U card and 2610XM router

insert7992
Level 1
Level 1

Hi,

I have a 2610XM router. On the router, I have only one fastethernet port and two blank WIC slots and one blank network module slot. When it starts, a error message says:

Slot is empty or does not support clock participate

WIC slot is empty or does not support clock participate

Then I bought a WIC-1B-U card and installed it on W0 slot, the error message remains there.

Here are my questions:

(1). none of the LED(B1,B2,NT1) on the WIC card is on. Is this normal? Does this mean that my router can not recognize the card?

(2). I checked the documents before I bought the WIC. It seems that WIC-1B-U does work with 2610XM. Can anyone confirm this issue?

(3). Is it a possible reason that corresponding configuration need to be set on the router to make it work? If so, what configuration do I need?

Thanks

Joe

3 Replies 3

owillins
Level 6
Level 6

Disable the " network-clock-participate "command

Wilson Samuel
Level 7
Level 7

Hi,

The simplest way to find out whether the WIC-1BU has been detected and accpted on a router is to go through the sh version output.

You should be seeing something similar to this:

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(23), RELEASE SOFTWARE (fc2)

Copyright (c) 1986-2004 by cisco Systems, Inc.

Compiled Wed 28-Jan-04 17:48 by kellmill

Image text-base: 0x8000808C, data-base: 0x81118968

ROM: System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)

Router uptime is 0 minutes

System returned to ROM by power-on

System image file is "flash:c2600-is-mz.122-23.bin"

cisco 2620 (MPC860) processor (revision 0x600) with 61440K/4096K bytes of memory.

Processor board ID JAD053604N6 (1074245753)

M860 processor: part number 0, mask 49

Bridging software.

X.25 software, Version 3.0.0.

Basic Rate ISDN software, Version 1.1.

1 FastEthernet/IEEE 802.3 interface(s)

1 Serial network interface(s)

1 ISDN Basic Rate interface(s) <= WIC-1BU Interface

32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Router#

Hope that helps,

Please rate all helpful posts.

Kind Regards,

Wilson Samuel

Thanks to both of you.

----------------------------------------------

To owillins:

Thanks but this does not work.I tried:

no network-clock-participate slot 1

no network-clock-participate wic 0

The error remains and all the LED are off.

----------------------------------------------

To Wilson:

My start up output does have the message of

1 ISDN Basic Rate interface

Hmmm, this prove that 2610XM does work with the card.

----------------------------------------------

To both of you and all:

It turns out I made a stupid mistake--I choose the wrong card. My internet connection is not ISDN based.

I'm trying to set up a subnetwork and using the 2610xm router (and a 2950 switch) to connect it with an university campus network. I think I should use an ethernet card(e.g. WIC-1ENET), am I right?

However, I found that, in the document, WIC-1ENET is not mentioned to be work with 2610XM. Can you guys give me a confirmation about the new choice? Or do you have better suggestion.

I've maken a mistake on buying the wrong card, which wasted money and time. I don't want to make the same mistake again. It would be very nice if someone with the similar experience can give me advice.

Thanks

Joe

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: