Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

WS-C3750X-48PF-S CPU Utilization

First of all I purchased the switches with part no. WS-C3750X-48P with the following IOS c3750e-universalk9-mz.150-1.SE1 & IOS feature license to work as ipservice.

Symptoms:

1)      - When running the switches in stack mode (connecting the booth switch with full-duplex stack) I found the cpu utilization on each switch reached to 34% The Hulc LED Process reaches to 20%

3)      - After about 1 hour  with no connections to the switch I found the status not changed.

4)      - I tried to run each switch in stand-alone mode (without stack cables connected) & monitor the status of the cpu utilization. I found it the same problem exist.

Actions taken:

1)      - Refereeing  to the internet I found a bug ID describing the status of the mentioned symptoms (attached)

2)      -  I made a down grade for the IOS version to be  c3750e-universalk9-mz.122-58.SE2.bin

3)      -  The mentioned IOS solved the Hulc LED Process (became 1 : 3 % ) & however cpu utilization became 18% with no links or traffic connected to the switches.

4)     - I guess that 18 % utilization is too much for a free switch (refer to the show run file) as I did not configure any advanced commands.

please advise with a suitable solution for the mentioned case ASAP

the required logs are attached

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
New Member

WS-C3750X-48PF-S CPU Utilization

Just my nickel's worth (a penny is worthless anymore)...

I worked at a site where we had Cisco 7206s, 3750's, etc. We used CA's Spectrum to monitor the CPU's.

And at my current site, we are running multiple 3750's in Layer 3 mode...

We don't get notifications unless the CPU goes above 50%, or bandwidth goes above 80%.

I understand that nothing is attached. But you'll have to compare a bare-bones device vs what you're running to see if there's a cause for concern.

I just looked at one of our 3750's. Granted, it's in the middle of the night here, but it's sitting at 13%.

I looked at another one; it's the master of a 5-stacked switch. It's sitting at 16%. It's average runs between 15-40%.

Just trying to give you perspective

6 REPLIES
New Member

WS-C3750X-48PF-S CPU Utilization

Just shut down the non-requried ports(many i believe ). I have faced the same issue.

Cheers

Arun

Purple

WS-C3750X-48PF-S CPU Utilization

  Thats not too high . People get too hung up on cpu that is above 20% .  The cpu generally has little to do with traffic switching these days which is handled in hardware. A 4500 will run 30-40% with nothing attched , this is normal also.

Hall of Fame Super Gold

WS-C3750X-48PF-S CPU Utilization

There are CPU bugs that are currently haunting 12.2(58)SE and 15.0(1)SE.  I'm testing 15.0(1)SE2 and it's alot better.  How about trying that?

New Member

WS-C3750X-48PF-S CPU Utilization

i already tried this version before without effect.....

New Member

WS-C3750X-48PF-S CPU Utilization

Just my nickel's worth (a penny is worthless anymore)...

I worked at a site where we had Cisco 7206s, 3750's, etc. We used CA's Spectrum to monitor the CPU's.

And at my current site, we are running multiple 3750's in Layer 3 mode...

We don't get notifications unless the CPU goes above 50%, or bandwidth goes above 80%.

I understand that nothing is attached. But you'll have to compare a bare-bones device vs what you're running to see if there's a cause for concern.

I just looked at one of our 3750's. Granted, it's in the middle of the night here, but it's sitting at 13%.

I looked at another one; it's the master of a 5-stacked switch. It's sitting at 16%. It's average runs between 15-40%.

Just trying to give you perspective

New Member

This might help https:/

This might help 

https://supportforums.cisco.com/discussion/11145246/high-cpu-hulk-led-process

1428
Views
0
Helpful
6
Replies
CreatePlease to create content