Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

WS-X6148-RJ-45 , WS-X6248-RJ-45 OIR

I just replaced the WS-X6248-RJ-45 with WS-X6148-RJ-45 within the same slot for Catalyst 6509 Switch . However , I can't config the FE port in WS-X6248-RJ-45 into switchport as below indicated :

(config-if)#interface FastEthernet7/4

(config-if)# no ip address

(config-if)# switchport

(config-if)# switchport mode access

Command rejected: Fa7/4 not a switching port.

While I put the WS-X6148-RJ-45 back to the same slot , the same error message appear , that mean I can't place the port for this subject slot (No matter with WS-X6148-RJ-45 or WS-X6248-RJ-45)

back to "switchport" any more .

I am wondering if the OIR for this two module make it happen and if I have to reboot the system to make it come back to normal condition as the default setting for the ports of these two module was supposed to be "switchport" !!

4 REPLIES
Cisco Employee

Re: WS-X6148-RJ-45 , WS-X6248-RJ-45 OIR

What happens when you give only the following commands:

(config-if)#interface FastEthernet7/4

(config-if)# no ip address

(config-if)# switchport

And then check, " Show int fa 7/4 switchport "

What is the IOS that you are running on the BOX. Please paste the "show version " and " show module" from the chassis.

Also try reseating the module back in the chassis and see if that makes any difference.

-amit singh

New Member

Re: WS-X6148-RJ-45 , WS-X6248-RJ-45 OIR

The system accept the command without reject message but I find the switchport status was "disabled" by "Show int fa 7/4 switchport" command . The show result was attached below !!

New Member

Re: WS-X6148-RJ-45 , WS-X6248-RJ-45 OIR

router> show version

Cisco Internetwork Operating System Software

IOS (tm) c6sup2_rp Software (c6sup2_rp-PSV-M), Version 12.1(13)E9, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Sat 12-Jul-03 20:41 by hqluong

Image text-base: 0x40008C00, data-base: 0x4179C000

ROM: System Bootstrap, Version 12.1(3r)E2, RELEASE SOFTWARE (fc1)

BOOTLDR: c6sup2_rp Software (c6sup2_rp-PSV-M), Version 12.1(13)E9, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

C80603-6509-01 uptime is 3 years, 46 weeks, 2 hours, 0 minutes

Time since C80603-6509-01 switched to active is 3 years, 46 weeks, 2 hours, 18 minutes

System returned to ROM by power-on (SP by power-on)

System restarted at 06:07:56 CST Tue Sep 9 2003

System image file is "slot0:c6sup22-psv-mz.121-13.E9.bin"

cisco Catalyst 6000 (R7000) processor with 458752K/65536K bytes of memory.

Processor board ID SAD05050HSY

R7000 CPU at 300Mhz, Implementation 39, Rev 2.1, 256KB L2, 1024KB L3 Cache

Last reset from power-on

X.25 software, Version 3.0.0.

Bridging software.

1 FlexWAN controller (1 ATM).

22 Virtual Ethernet/IEEE 802.3 interface(s)

240 FastEthernet/IEEE 802.3 interface(s)

20 Gigabit Ethernet/IEEE 802.3 interface(s)

1 ATM network interface(s)

381K bytes of non-volatile configuration memory.

16384K bytes of Flash internal SIMM (Sector size 512K).

Standby is up

Standby has 458752K/65536K bytes of memory.

Configuration register is 0x2102

router> show module ---> 6148

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-SUP2-2GE SAD05060NE0

2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-SUP2-2GE SAD05060NGF

3 0 2 port adapter FlexWAN WS-X6182-2PA SAD06070554

4 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAD05040L3E

5 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAD05040LAE

7 48 48-port 10/100 mb RJ45 WS-X6148-RJ-45 SAL08229EJ9

8 48 48 port 10/100 mb RJ-45 ethernet WS-X6248-RJ-45 SAD04270NDF

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0002.7ec1.0dea to 0002.7ec1.0deb 2.2 6.1(3) 7.5(0.6)HUB1 Ok

2 0001.6414.eee6 to 0001.6414.eee7 2.2 6.1(3) 7.5(0.6)HUB1 Ok

3 0002.7e38.b2ec to 0002.7e38.b32b 1.4 12.1(13)E9 12.1(13)E9 Ok

4 0001.c9b0.ab3c to 0001.c9b0.ab43 1.4 5.4(2) 7.5(0.6)HUB1 Ok

5 0001.c9b0.acfc to 0001.c9b0.ad03 1.4 5.4(2) 7.5(0.6)HUB1 Ok

7 0011.213b.e448 to 0011.213b.e477 3.1 5.4(2) 7.5(0.6)HUB1 Ok

8 0002.fc23.1e28 to 0002.fc23.1e57 1.4 5.4(2) 7.5(0.6)HUB1 Ok

Mod Sub-Module Model Serial Hw Status

--- --------------------------- --------------- --------------- ------- -------

1 Policy Feature Card 2 WS-F6K-PFC2 SAD05060LP5 1.3 Ok

1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAD05050HSY 1.2 Ok

2 Policy Feature Card 2 WS-F6K-PFC2 SAD05060LU3 1.3 Ok

2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAD05060R68 1.2 Ok

Mod Online Diag Status

--- -------------------

1 Pass

2 Pass

3 Not Supported

4 Pass

5 Pass

7 Pass

8 Pass

New Member

Re: WS-X6148-RJ-45 , WS-X6248-RJ-45 OIR

router> show module ---> 6248

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-SUP2-2GE SAD05060NE0

2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-SUP2-2GE SAD05060NGF

3 0 2 port adapter FlexWAN WS-X6182-2PA SAD06070554

4 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAD05040L3E

5 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAD05040LAE

7 48 48 port 10/100 mb RJ-45 ethernet WS-X6248-RJ-45 SAD041509N5

8 48 48 port 10/100 mb RJ-45 ethernet WS-X6248-RJ-45 SAD04270NDF

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0002.7ec1.0dea to 0002.7ec1.0deb 2.2 6.1(3) 7.5(0.6)HUB1 Ok

2 0001.6414.eee6 to 0001.6414.eee7 2.2 6.1(3) 7.5(0.6)HUB1 Ok

3 0002.7e38.b2ec to 0002.7e38.b32b 1.4 12.1(13)E9 12.1(13)E9 Ok

4 0001.c9b0.ab3c to 0001.c9b0.ab43 1.4 5.4(2) 7.5(0.6)HUB1 Ok

5 0001.c9b0.acfc to 0001.c9b0.ad03 1.4 5.4(2) 7.5(0.6)HUB1 Ok

7 0001.9712.8530 to 0001.9712.855f 1.2 5.1(1)CSX 7.5(0.6)HUB1 Ok

8 0002.fc23.1e28 to 0002.fc23.1e57 1.4 5.4(2) 7.5(0.6)HUB1 Ok

Mod Sub-Module Model Serial Hw Status

--- --------------------------- --------------- --------------- ------- -------

1 Policy Feature Card 2 WS-F6K-PFC2 SAD05060LP5 1.3 Ok

1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAD05050HSY 1.2 Ok

2 Policy Feature Card 2 WS-F6K-PFC2 SAD05060LU3 1.3 Ok

2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAD05060R68 1.2 Ok

Mod Online Diag Status

--- -------------------

1 Pass

2 Pass

3 Not Supported

4 Pass

5 Pass

7 Pass

8 Pass

446
Views
0
Helpful
4
Replies
CreatePlease to create content