Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

WS-X6348-RJ-45 Card Problem

I recently purchased a replacement WS-X6348-RJ-45 card for my 6509

platform. When I slide the card into the chassis the card powers up,

then after a minute or two it powers itself down. It does the same

thing if the "power enable" command is issued. The log shows only

the following output:

*Aug 6 11:06:44: %C6KPWR-SP-4-ENABLED: power to module in slot 7 set

on

*Aug 6 11:08:14: %C6KPWR-SP-4-DISABLED: power to module in slot 7 set

off (admin request)

I'm running IOS version 12.1(8b)E20 with 7 more of these same cards in

the unit functioning fine. I've tested the slot with a known good

card and it works fine. I have also moved the questionable card to

known good slot and it does the same thing. At this point I either

have a bad or incompatible card. The only reason I say incompatible

is because of the hardware rev shown when I do a "show module" is

quite a bit higher than the others as seen in the output below:

Mod Ports Card Type Model

Serial No.

--- ----- -------------------------------------- ------------------

-----------

1 2 Cat 6000 sup 1 Enhanced QoS (Active) WS-X6K-SUP1A-2GE

SAD041104EX

2 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45

SAL04493Z8M

3 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45

SAD04310BW9

4 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45

SAD04250183

5 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45

SAD041600UT

6 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45

SAL04493Z8M

7 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45

SAL0808UPCW

8 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45

SAL0437186M

9 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45

SAL04341PAV

Mod MAC addresses Hw Fw

Sw Status

--- ---------------------------------- ------ ------------

------------ -------

1 0030.9631.ebd4 to 0030.9631.ebd5 3.1 5.1(1)

6.2(2.113) Ok

2 0003.6c15.1aa0 to 0003.6c15.1acf 1.4 5.4(2)

6.2(2.113) Other

3 0002.fc62.2c10 to 0002.fc62.2c3f 1.1 5.3(1)

6.2(2.113) Ok

4 0030.b63a.cf10 to 0030.b63a.cf3f 2.1 5.4(2)

6.2(2.113) Ok

5 00d0.d3a1.9208 to 00d0.d3a1.9237 1.1 5.3(1)

6.2(2.113) Ok

6 0003.6c15.1aa0 to 0003.6c15.1acf 1.4 5.4(2)

6.2(2.113) Ok

7 000f.240b.89f4 to 000f.240b.8a23 9.0 Unknown

Unknown Other

8 0001.9756.91d0 to 0001.9756.91ff 1.4 5.4(2)

6.2(2.113) Ok

9 0002.fc1c.a178 to 0002.fc1c.a1a7 1.1 5.4(2)

6.2(2.113) Ok

Mod Sub-Module Model Serial

Hw Status

--- --------------------------- --------------- ---------------

------- -------

1 Policy Feature Card WS-F6K-PFC SAD042702D9

1.1 Ok

1 MSFC Cat6k daughterboard WS-F6K-MSFC SAD041009E0

1.4 Ok

As you can see the card in question, card 7, is on hw rev 9.0 which is

quite a bit higher than the rest. What I don't know is if this is the

problem or if I have a bad card. I haven't been able to find a

matrix saying what hw revs are supported by what software revs.

Can anyone shed some light on this for me?

Thanks,

Mike

2 REPLIES
Hall of Fame Super Bronze

Re: WS-X6348-RJ-45 Card Problem

You've done your homework. It's a faulty hardware. Call Cisco and ask for a RMA.

New Member

Re: WS-X6348-RJ-45 Card Problem

Thank you for the reply. It was very helpful.

156
Views
4
Helpful
2
Replies