Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

mrm - "Monitor source address is not configured"?

Greetings,

I'm trying to use MRM, but the "manager" doesn't seem to know it's source address, despite looking like it does.

I've tried multiple source interfaces.

-----------------------------------------ip mrm manager TEST

manager Serial0/0.1 group 225.0.0.1

senders 1

receivers 2

-----------------------------------------

R3#sh ip mrm manager TEST

Manager:TEST/1.0.0.1 is not running

Beacon interval/holdtime/ttl:60/86400/32

Group:225.0.0.1, UDP port test-packet/status-report:16384/65535

Test senders:

5.5.5.5

Test receivers:

1.1.1.1

-----------------------------------------

R3#mrm TEST start

Monitor source address is not configured

-----------------------------------------

???!!!! Another interface (loopback)

-----------------------------------------

R3#sh ip mrm manager TEST

Manager:TEST/3.3.3.3 is not running

Beacon interval/holdtime/ttl:5/86400/32

Group:239.0.0.1, UDP port test-packet/status-report:50000/50001

Test senders:

5.5.5.5

Test receivers:

1.1.1.1

R3#mrm TEST start

Monitor source address is not configured

-----------------------------------------

I've tried this on various 3640s running enterprise 12.3, and a 2500 running 12.2(32). All have the same result.

1 ACCEPTED SOLUTION

Accepted Solutions

Re: mrm - "Monitor source address is not configured"?

You have missed this command, I believe.

"R1(config-mrm-manager)# receivers 2 sender-list 1"

Although the Cisco IOS CLI parser accepts the command entered without the sender-list access-list keyword-argument pair, this keyword-argument pair is not optional. For an MRM test to work, you must specify the sources that the Test Receiver should monitor using the sender-list keyword and access-list argument.

This should solve the problem.

HTH-Cheers,

Swaroop

========================================

[[[ This is a 3600 O/P from Dynamips ]]]

R1#sh ip mrm in

R1#sh ip mrm interface

Interface Address Mode Status

FastEthernet0/0 10.1.1.1 Test-Receiver Up

R1#mrm TEST1 ?

start Start IP MRM test

stop Stop IP MRM test

R1#mrm TEST1 start

R1#mrm TEST1 start

R1#

R1#

R1#sh

00:06:23: IP MRM test 'TEST1' starts ......

% Type "show ?" for a list of subcommands

R1#

R1#

R1#

R1#sh ip mrm manager

Manager:TEST1/10.1.2.1 is running, expire:1d00h

Beacon interval/holdtime/ttl:60/86400/32

Group:239.1.1.1, UDP port test-packet/status-report:16384/65535

Test senders:

10.1.1.2 /N-Ack

Test receivers:

10.1.2.2 /N-Ack

R1#sh ip mrm manager

Manager:TEST1/10.1.2.1 is running, expire:1d00h

Beacon interval/holdtime/ttl:60/86400/32

Group:239.1.1.1, UDP port test-packet/status-report:16384/65535

Test senders:

10.1.1.2 /N-Ack

Test receivers:

10.1.2.2 /N-Ack

R1#

!

ip mrm manager TEST1

manager FastEthernet1/0 group 239.1.1.1

senders 1

receivers 2 sender-list 1

!

access-list 1 permit 10.1.1.2

access-list 2 permit 10.1.2.2

!

!

R1#sh cdp nei

Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge

S - Switch, H - Host, I - IGMP, r - Repeater

Device ID Local Intrfce Holdtme Capability Platform Port ID

R2 Fas 0/0 135 R 3620 Fas 0/0

R3 Fas 1/0 172 R 3620 Fas 0/0

R1#

R1#

R1#sh ip int brie

Interface IP-Address OK? Method Status Prot

ocol

FastEthernet0/0 10.1.1.1 YES manual up up

FastEthernet1/0 10.1.2.1 YES manual up up

Loopback0 1.1.1.1 YES manual up up

R1#

----------------------------

1 REPLY

Re: mrm - "Monitor source address is not configured"?

You have missed this command, I believe.

"R1(config-mrm-manager)# receivers 2 sender-list 1"

Although the Cisco IOS CLI parser accepts the command entered without the sender-list access-list keyword-argument pair, this keyword-argument pair is not optional. For an MRM test to work, you must specify the sources that the Test Receiver should monitor using the sender-list keyword and access-list argument.

This should solve the problem.

HTH-Cheers,

Swaroop

========================================

[[[ This is a 3600 O/P from Dynamips ]]]

R1#sh ip mrm in

R1#sh ip mrm interface

Interface Address Mode Status

FastEthernet0/0 10.1.1.1 Test-Receiver Up

R1#mrm TEST1 ?

start Start IP MRM test

stop Stop IP MRM test

R1#mrm TEST1 start

R1#mrm TEST1 start

R1#

R1#

R1#sh

00:06:23: IP MRM test 'TEST1' starts ......

% Type "show ?" for a list of subcommands

R1#

R1#

R1#

R1#sh ip mrm manager

Manager:TEST1/10.1.2.1 is running, expire:1d00h

Beacon interval/holdtime/ttl:60/86400/32

Group:239.1.1.1, UDP port test-packet/status-report:16384/65535

Test senders:

10.1.1.2 /N-Ack

Test receivers:

10.1.2.2 /N-Ack

R1#sh ip mrm manager

Manager:TEST1/10.1.2.1 is running, expire:1d00h

Beacon interval/holdtime/ttl:60/86400/32

Group:239.1.1.1, UDP port test-packet/status-report:16384/65535

Test senders:

10.1.1.2 /N-Ack

Test receivers:

10.1.2.2 /N-Ack

R1#

!

ip mrm manager TEST1

manager FastEthernet1/0 group 239.1.1.1

senders 1

receivers 2 sender-list 1

!

access-list 1 permit 10.1.1.2

access-list 2 permit 10.1.2.2

!

!

R1#sh cdp nei

Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge

S - Switch, H - Host, I - IGMP, r - Repeater

Device ID Local Intrfce Holdtme Capability Platform Port ID

R2 Fas 0/0 135 R 3620 Fas 0/0

R3 Fas 1/0 172 R 3620 Fas 0/0

R1#

R1#

R1#sh ip int brie

Interface IP-Address OK? Method Status Prot

ocol

FastEthernet0/0 10.1.1.1 YES manual up up

FastEthernet1/0 10.1.2.1 YES manual up up

Loopback0 1.1.1.1 YES manual up up

R1#

----------------------------

423
Views
0
Helpful
1
Replies