Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

rate-limit 3750me

I’m trying to rate-limit the traffic going thought a Fast Ethernet interface on a ME3750 to 2MB. I have 2 VLANs going through, and I want to trust the CoS values because it can be different types of priority traffic inside the two VLANs. I would like the switch to drop packets with low priority first no matter what VLAN tag it has. I can also use the ES ports if it's any limitation on the fast Ethernet ports.

I tried to configure QoS in the lab, but it didn’t work properly. For this test I’ve used SmartBit to send trafikk between int fa1/0/9 and 1/0/10:

Interface fa1/0/9: VLAN 25 (11MB, Pri 0) and VLAN 24 (3MB, Pri 6)

Interface fa1/0/10: VLAN 25 (11MB, Pri 0) and VLAN 24 (3MB, Pri 6)

mls qos

Policy Map customer-policy-A

    Class class-default

            police 2000000 8000 exceed-action drop

            trust cos

interface FastEthernet1/0/9

switchport trunk encapsulation dot1q

           switchport trunk allowed vlan 24,25

           switchport mode trunk

           speed 100

           duplex full

           service-policy input customer-policy-A

interface FastEthernet1/0/10

switchport trunk encapsulation dot1q

switchport trunk allowed vlan 24,25

switchport mode trunk

speed 100

duplex full

service-policy input customer-policy-A

With this configuration I got 83% packet loss, but also for the priority traffic (all 4 flows got 83% pct loss). Seems to me that the trust function didn’t work.. ?

Everyone's tags (7)
5 REPLIES
New Member

Re: rate-limit 3750me

Hi,  here is my suggestion:  You need to another policy-map that you can call "customer-policy-B". you the same configs customer-policy-A but add conform-action set-cos-transmit 3 ( you can choose any cos depending on your network).  create a class-map for each vlan. i.e: (config)#class-map vlan_24                                                  match vlan 24                                         (config)#class-map vlan_25                                                  match vlan 25  create a second policy-map. i.e: (config)#policy-map test                                            class vlan_24                                             service-policy input customer-policy-A                                            class vlan_25                                             service-policy input customer-policy-B Apply the "test" policy on your trunk interfaces.  Pls let me know your results.

Posted from my mobile device.

New Member

Re: rate-limit 3750me

 

Hi, thank you for your answer. Looks like I don't have the command "conform-action set-cos-transmit 3" on my 3750 switch. I could try with policed -dscp-transmit, but I it also looks like the configuration won't work for my fast Ethernet ports. I got a message about using ES ports for hierarchical service-police. I really would like to use the Fast Ethernet ports.. is it possible?

New Member

Re: rate-limit 3750me

Hi,

this URL will help you : https://www.cisco.com/en/US/products/hw/switches/ps5023/products_tech_note09186a0080883f9e.shtml

It covers all the qos on the 3750. the "conform-action" is on the Me3400. Instead, you can "set" command and set the cos or the dscp that you prefer. i.e set cos 5 for the class vlan you want to priotize.

Regards

New Member

Re: rate-limit 3750me

Thanks!

Can you recommend a simple way to configure rate limit for all traffic going through a fast ethernet port(dot1q)?

- limit all traffic to 2 MB

- trust cos tagging

- drop packets with low priority (regardless of vlan tag) Lets say drop Pri 0 - 4

If it's not possible, can it easily  be done within just one vlan? I tried with SVI based, but got a message about "police action on parent level not supported for vlan..".

New Member

Re: rate-limit 3750me

Hi,

i haven't encounter the scenario that you set below.

i guess you will need either an access-lists or a route-map (not sure if supported on 3750). You match cos or dscp value that you want to allow and deny everything else.

Then you create a class-map that match with the route-map you created earlier. After that you create a policy-map with the class that you created. Then police 2048000 exceed-action drop.

At the physical interface, you apply the policy-map.

sample configs: route-map allow

                         match cos 5

                         match cos 3

                         deny any

                       class-map transmit

                            match route-map allow

                       policy-map physical

                          class transmit

                             police 2048000 exceed-action drop

                       interface fast0/1

                         service-policy input physical

NB: in case of an access-list: you will match all priority you desire to transmit. since there is an implicit deny at bottom of an access-list, you don't really need to deny again. Afterward, follow the same procedure for route-map.

2699
Views
0
Helpful
5
Replies
CreatePlease to create content