Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Adding a Connection on MGX 8850 (with PXM-1E)

Dear all,

I've MGX 8850 [ with PXM-1E (with 8 E3) and RPM-PR (NPE400) processor ] .....It's acting as an ATM edge-LSR in our cell-mode MPLS network

(This network is based on MGX 8850 with RPM-PR acting as ATM edge-LSRs and the BPX 8600 with LSC 7200 acting as the ATM LSR)

The problem is that I'm facing difficulties in adding connections between the PXM-1E (slave) and RPM-PR (Master).

1- RPM-PR IOS ver is 12.2(11)T2

2- PXM ver is 3.0(20.0)

3- The steps I follow for PXM-1E config are

a- upln 2.1

b- cnfln -e3 2.1 -len 30 -clk 2

c- addport 1 2.1 80000 80000 0 1

80000 ----->guaranteeRate in cells/sec

80000------> maxRate in cells/sec

0------------> sctId -- SCT file ID between 0 and 255, for default file use 0

1------------> ifType -- 1: uni 2: nni 3: vnni 4: vuni 5: evuni 6: evnni

d- TOTO.7.PXM.a > dsplns

Line Line Line Line Length OOF AIS Valid Alarm

Num State Type Lpbk (meters) Criteria cBitsCheck Intvls State

----- ----- ----------- ---------- ------- -------- ---------- ------ -------

2.1 Up e3g832adm NoLoop 0 N/A N/A 96 Clear

e- TOTO.7.PXM.a > dspports

ifNum Line Admin Operational Guaranteed Maximum sctID ifType VPI MI

NVPI MAXVPI IMA

State State Rate Rate Conf./InUse (VNNI, (E

VUNI, (EVUNI, GRP

VUNI) E

VNNI) EVNNI)

----- ---- ----- -------------- ---------- ------- ------------ ------ ------ --

----- ------- ---

1 2.1 Up Up 80000 80000 0/ 0 =Def UNI 0

f- addpart 1 4 4 100 100 100 100 0 255 1 65535 1000 2000

1-----> If Number -- number between 1 and 31

4-----> Partition Number -- Partition Identifier between 1 and 20

4-----> Controller Number -- Controller Identifier between 1 and 254

cntrlrIds 2 and 3 are reserved for PNNI and LSC respect

100----> Egr guaranteed % Bandwidth -- units:0.0001% of interface bandwidth

100----> Egr max % Bandwidth -- units:0.0001% of interface bandwidth

100-----> Ing guaranteed % Bandwidth -- units:0.0001% of interface bandwidth

100-----> Ing max % Bandwidth -- units:0.0001% of interface bandwidth

0--------> Minimum VPI Value -- number between 0 and 4095(0..255 for UNI interface

255----> Maximum VPI Value -- number between 0 and 4095(0..255 for UNI interfac

1-------> Minimum VCI Value -- number between 1 and 65535

65535-----> Maximum VCI Value -- number between 1 and 65535

1000----> Guaranteed number of conns -- number between 0 and 27000

between 10 and 13500 for PXM1E-16-T1E1

2000---->Max. number of conns -- number between 10 and 27000

between 10 and 13500 for PXM1E-16-T1E1

g- TOTO.7.PXM.a > dspparts

if part Ctlr egr egr ingr ingr min max min max min max

Num ID ID GuarBw MaxBw GuarBw MaxBw vpi vpi vci vci conn conn

(.0001%)(.0001%)(.0001%)(.0001%)

-----------------------------------------------------------------------------

1 4 4 100 100 100 100 0 255 1 65535 1000 2000

h-TOTO.7.PXM.a > addcon

Err: Mandatory argument required.

Syntax: addcon ifNum vpi vci serviceType mastership

g- addcon 1 4 0 1 2

1-----> ifNum -- interface number (1..31)

4 ----> vpi -- vpi (UNI: 0..255 | NNI: 0..4095)

0------> vci -- vci: VCC (1..65535); VPC (0)

1------> serviceType -- cbr1(1) | vbr1rt(2) | vbr2rt(3) |

vbr3rt(4) | vbr1nrt(5) | vbr2nrt(6) |

vbr3nrt(7) | ubr1(8) | ubr2(9) |

2-----> mastership -- m (1) | s (2)

ERR: Error sending pass up message

I'd like to know what and why this error appear to me while i'm adding the connection ....wht's wrong??

Plz can anyone advise??

Regards,

Komy

1 REPLY
Bronze

Re: Adding a Connection on MGX 8850 (with PXM-1E)

This release note document talks about the features and limitations of the hardware and release that you are using. Check if it helps in solving your problem :

http://www.cisco.com/univercd/cc/td/doc/product/wanbu/8850px45/relnote/30208850.htm

309
Views
0
Helpful
1
Replies
CreatePlease to create content