08-18-2003 10:33 PM
When trying to configure the connect
if the source interface of the AtoM [PW/l2transport] is
on of the above PA-MCX-8TE1, it doesnt
give the opportunity to finish the
l2transport configuration.
The MPLS route part doesn't show at ALL!!!
MPLS is over the ATM port, and is IP MPLS,
not ATM MPLS.
Any ideas?
Here is the router sh ver, sh diag:
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-JS-M), Version 12.2(14)S3, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Tue 01-Jul-03 17:53 by kellythw
Image text-base: 0x60008BD4, data-base: 0x6187A000
ROM: System Bootstrap, Version 12.1(20000710:044039) [nlaw-121E_npeb 117], DEVELOPMENT SOFTWARE
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(13)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
xxx uptime is 1 week, 1 day, 16 hours, 33 minutes
System returned to ROM by power-on
System restarted at 16:52:33 EET Sun Aug 10 2003
System image file is "sup-slot0:/c7200-js-mz.122-14.S3.bin"
cisco 7206VXR (NPE400) processor (revision A) with 245760K/16384K bytes of memory.
Processor board ID 26790689
R7000 CPU at 350Mhz, Implementation 39, Rev 3.2, 256KB L2, 4096KB L3 Cache
6 slot VXR midplane, Version 2.6
Last reset from watchdog reset
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
Channelized E1, Version 1.0.
1 FastEthernet/IEEE 802.3 interface(s)
30 Serial network interface(s)
1 ATM network interface(s)
8 Channelized E1/PRI port(s)
125K bytes of non-volatile configuration memory.
sh diags:
Slot 0:
Fast-ethernet on C7200 I/O card with MII or RJ45 Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time 1w1d ago
EEPROM contents at hardware discovery:
Hardware revision 2.2 Board revision A0
Serial number 23932000 Part number 73-4092-04
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 83 02 02 01 6D 2C 60 49 0F FC 04 00 00 00 00
0x30: 50 00 00 00 01 11 24 00 00 00 FF FF FF FF FF FF
Slot 1:
Mx serial (V.35) Port adapter, 8 ports
Port adapter is analyzed
Port adapter insertion time 1w1d ago
EEPROM contents at hardware discovery:
Hardware revision 1.17 Board revision A0
Serial number 27600372 Part number 73-1580-10
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0D 01 11 01 A5 25 F4 49 06 2C 0A 00 00 00 00
0x30: 50 00 00 00 02 01 15 00 FF FF FF FF FF FF FF FF
Slot 2:
PA-MCX-8TE1 Port adapter, 8 ports
Port adapter is analyzed
Port adapter insertion time 1w1d ago
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
PCB Serial Number : MIC040400M1
Part Number : 73-4118-04
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0-0
Product Number : PA-MCX-8TE1
Top Assy. Part Number : 800-05358-04
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 01 7A 41 01 00 C1 8B 4D 49 43 30 34 30
0x10: 34 30 30 4D 31 82 49 10 16 04 42 41 30 03 00 81
0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D
0x30: 4D 43 58 2D 38 54 45 31 20 20 20 20 20 20 20 20
0x40: 20 C0 46 03 20 00 14 EE 04 FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Slot 4:
ATM WAN OC3 (SMI) Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time 1w1d ago
EEPROM contents at hardware discovery:
Hardware revision 2.0 Board revision A0
Serial number 28283420 Part number 73-2427-04
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 56 02 00 01 AF 92 1C 49 09 7B 04 00 00 00 00
0x30: 50 00 00 00 02 06 07 00 FF FF FF FF FF FF FF FF
Solved! Go to Solution.
08-22-2003 07:16 AM
This document talks about platform support for AtoM, I don't see the port adapter that you are using in this list. Check it out :
08-22-2003 07:16 AM
This document talks about platform support for AtoM, I don't see the port adapter that you are using in this list. Check it out :
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide