04-25-2012 09:40 PM
Hi,
We just bought a Cisco 7204 VXR NPE-G1 with IOS
c7200-is-mz.123-15b.bin.
I would like to configure it for our MPLS lab router, can I upgrade this router to support MPLS protocol.
Please need your assistance.
regards
Navi
04-26-2012 04:53 AM
hi Navi,
you might use http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp for these queries in the future, 12.3-15b does support MPLS as well, you just need SERVICE PROVIDER feature set.
HTH!
04-26-2012 02:03 PM
Hi Ivan,
Thanks for your response.
OK, the Cisco tool is a little bit hard to get.
What I requested for is that…..Can the Cisco 7204 NPE-G1 upgradeable to support MPLS? (the current IOS is this router Cisco 7204 router is C7200-is-mz.123-15b.bin
Regards
Navi
04-26-2012 02:06 PM
Hi Navi,
yes it can, platform-wise, you just need a proper IOS image for that. What do you have in 'sh ver' at the moment?
04-26-2012 02:18 PM
Hi Iavn
Below is the sh version
Router#sh version
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-IS-M), Version 12.3(15b), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 25-Aug-05 19:08 by ssearch
Image text-base: 0x60008AF4, data-base: 0x61CB8000
ROM: System Bootstrap, Version 12.3(4r)T3, RELEASE SOFTWARE (fc1)
BOOTLDR: 7200 Software (C7200-KBOOT-M), Version 12.3(15b), RELEASE SOFTWARE (fc1)
Router uptime is 4 hours, 55 minutes
System returned to ROM by power-on
System image file is "disk2:c7200-is-mz.123-15b.bin"
cisco 7204VXR (NPE-G1) processor (revision C) with 491520K/32768K bytes of memory.
Processor board ID 30882615
SB-1 CPU at 700MHz, Implementation 1, Rev 0.2, 512KB L2 Cache
4 slot VXR midplane, Version 2.8
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port
Adaptor Hardware Configuration Guidelines" on CCO
for c7200 bandwidth points oversubscription/usage guidelines.
3 Gigabit Ethernet/IEEE 802.3 interface(s)
509K bytes of non-volatile configuration memory.
62720K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).
16384K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102
Regards
navi
04-26-2012 02:54 PM
Right, it is an IP PLUS image, you would need this:
c7200-p-mz.123-15b.bin
to run MPLS.
04-26-2012 04:42 PM
Thanks….
I have an existing 7206 NPE-G2 router with sh version below. Can I upgrade the 7204 IP Plus image to the 7206 NPE-G2 image?
Cisco IOS Software, 7200 Software (C7200P-SPSERVICESK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Thu 26-Feb-09 01:45 by prod_rel_team
ROM: System Bootstrap, Version 12.4(12.2r)T, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, 7200 Software (C7200P-KBOOT-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)
SUV-IP-RTR-ER01 uptime is 2 years, 33 weeks, 3 days, 34 minutes
System returned to ROM by reload at 08:03:24 FJT Sun Sep 6 2009
System restarted at 08:13:41 FJST Sun Sep 6 2009
System image file is "disk2:c7200p-spservicesk9-mz.124-24.T.bin"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory.
Processor board ID 36575575
MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2
6 slot VXR midplane, Version 2.11
Last reset from power-on
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <>>
for c7200 bandwidth points oversubscription and usage guidelines.
1 FastEthernet interface
3 Gigabit Ethernet interfaces
2045K bytes of NVRAM.
250880K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
04-26-2012 06:06 PM
04-26-2012 07:48 PM
Hi Ivan,
How can I get this image?
04-26-2012 10:56 PM
Navi,
if you mean "NPE-G2" image, then it is not possible 'cause it is a different CPU type, not image. In other words if you wish upgrade from NPE-G1 to NPE-G2, you need to change hardware rather than software.
I hope this is clear now.
Cheers!
04-29-2012 06:22 PM
Thanks Ivan,
It’s clear now.
Do you have any idea of where we can get the below IOS from? I notice that the NPE-G1 is not supported with Cisco anymore.
c7200-p-mz.123-15b.bin
Regards
Navi
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide