Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

DSL Interfarface over ATM

Hello,

The list below is an output of "show dsl interface ATM 0". Can soneone explain this output and what are the limits values.

show dsl interface ATM 0

ATU-R (DS) ATU-C (US)

Modem Status: Showtime (DMTDSL_SHOWTIME)

DSL Mode: ITU G.992.1 (G.DMT)

ITU STD NUM: 0x01 0x01

Vendor ID: 'ALCB' 'ANDV'

Vendor Specific: 0x0000 0x0000

Vendor Country: 0x00 0x00

Capacity Used: 40% 22%

Noise Margin: 22.0 dB 31.0 dB

Output Power: 20.0 dBm 10.5 dBm

Attenuation: 45.5 dB 28.5 dB

Defect Status: None None

Last Fail Code: Protocol error

Selftest Result: 0x00

Subfunction: 0x15

Interrupts: 647 (1 spurious)

Activations: 1

Init FW: embedded

Operartion FW: embedded

SW Version: 3.919

FW Version: 0x1A04

Interleave Fast Interleave Fast

Speed (kbps): 0 1856 0 128

Reed-Solomon EC: 0 0 0 0

CRC Errors: 0 14 0 96

Header Errors: 0 2 0 6

Bit Errors: 0 0

BER Valid sec: 0 0

BER Invalid sec: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin

00: 0 0 0 0 0 0 0 0 0 0 0 2 3 4 4 4

10: 4 4 4 4 4 3 3 3 2 2 2 0 0 0 0 0

20: 0 0 0 0 0 0 0 2 2 2 3 4 4 4 4 5

30: 5 5 5 5 5 5 5 6 6 6 6 6 4 6 6 6

40: 0 4 4 5 5 6 5 6 5 6 5 5 6 5 5 6

50: 6 6 6 6 6 6 6 6 5 5 5 5 6 5 5 5

60: 5 2 5 5 5 4 5 5 5 5 5 5 5 5 5 5

70: 3 4 4 4 4 5 5 4 2 4 4 2 4 4 4 4

80: 2 4 2 2 4 2 2 4 4 4 4 4 4 4 4 4

90: 4 3 3 2 2 0 2 2 0 2 2 2 2 2 2 2

A0: 2 2 2 0 2 2 2 2 0 2 0 2 2 2 2 2

B0: 2 2 0 0 0 2 2 2 2 0 0 0 0 0 0 0

C0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

D0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

E0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Training log buffer capability is not enabled yet.

TIA

Mario

1 REPLY
Bronze

Re: DSL Interfarface over ATM

The outputs basically display the layer-1 and layer-2 parameters for the DSL interface. See if this link helps you :

http://www.cisco.com/en/US/products/hw/routers/ps221/products_implementation_design_guide09186a00800faf11.html

150
Views
0
Helpful
1
Replies