02-18-2006 07:55 AM
Hi,
is there any IOS version available, which supports MPLS. This is only required in a lab for CCIP preparation.
Frank
Solved! Go to Solution.
03-04-2006 08:43 AM
3620(config-if)#mpls label protocol ?
both Use LDP or TDP (Adapt to peer on multiaccess interface)
ldp Use LDP
tdp Use TDP (default)
3620#show ver
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3620-J1S3-M), Version 12.2(13)T16, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 14-Apr-05 22:31 by yiyan
Image text-base: 0x6000891C, data-base: 0x619D4000
ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
ROM: 3600 Software (C3620-I-M), Version 11.2(26)P, RELEASE SOFTWARE (fc1)
fr uptime is 1 day, 11 hours, 55 minutes
System returned to ROM by power-on
System image file is "flash:c3620-j1s3-mz.122-13.T16.bin"
cisco 3620 (R4700) processor (revision 0x81) with 61440K/4096K bytes of memory.
Processor board ID XXXXXXXX
R4700 CPU at 80Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
TN3270 Emulation software.
8 Low-speed serial(sync/async) network interface(s)
29K bytes of non-volatile configuration memory.
24576K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
02-18-2006 08:11 AM
MPLS is not supported on the 3620.
Hope this helps,
02-27-2006 03:17 AM
MPLS support was in 12.2(16) Enterprise even for 2600 routers. I think it might be supported for 3600 also.
At least for lab purposes.
02-27-2006 04:05 AM
Thanks for your feedback.
I have running IOS 12.2 Enterprise but this version is supporting tag switching only (tdp and no ldp).
For my purposes is it sufficient.
Frank
02-27-2006 09:41 AM
Frank,
12.3 or 12.2.15T Enterprise version support mpls ldp in the 2600 platform. Tdp, Cisco pre-standardize implementation method, is a subset of the ldp. To learn MPLS and VPN concept, you really don't need ldp, in my opinion, unless you dig deep into InterAS, Carrier over Carrier, TE, or AToM feature sets.
Edwin
03-04-2006 08:43 AM
3620(config-if)#mpls label protocol ?
both Use LDP or TDP (Adapt to peer on multiaccess interface)
ldp Use LDP
tdp Use TDP (default)
3620#show ver
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3620-J1S3-M), Version 12.2(13)T16, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 14-Apr-05 22:31 by yiyan
Image text-base: 0x6000891C, data-base: 0x619D4000
ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
ROM: 3600 Software (C3620-I-M), Version 11.2(26)P, RELEASE SOFTWARE (fc1)
fr uptime is 1 day, 11 hours, 55 minutes
System returned to ROM by power-on
System image file is "flash:c3620-j1s3-mz.122-13.T16.bin"
cisco 3620 (R4700) processor (revision 0x81) with 61440K/4096K bytes of memory.
Processor board ID XXXXXXXX
R4700 CPU at 80Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
TN3270 Emulation software.
8 Low-speed serial(sync/async) network interface(s)
29K bytes of non-volatile configuration memory.
24576K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
03-06-2006 03:08 AM
Thanks a lot.
It works and will improve my preparation for the CCIP exam.
Frank
02-28-2006 08:03 AM
I'm running 12.0(24.4)S2 in my lab and it supports LDP, etc.
joel_pe1#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3620-K4P-M), Version 12.0(24.4)S2, EARLY DEPLOYMENT MAINTENANCE INTERIM SOFTWARE
cisco 3620 (R4700) processor (revision 0x81) with 49152K/16384K bytes of memory.
joel_pe1#sh mpls ldp nei
Peer LDP Ident: 154.11.0.4:0; Local LDP Ident 154.11.0.2:0
joel_pe1#dir
Directory of flash:/
1 -rw- 6353696
08-20-2011 04:52 AM
Hi,
I realise this thread is very old, and the 3620 even older and unsupported now, but ive got a bunch of them lying around and was trying to do an MPLS lab with them.
Looks like "c3620-j1s3-mz.122-13.T16.bin" is not available on CCO for download any more, and "c3620-j1s3-mz.123-26.bin" which is on my box does not support MPLS (would have thought it carried features from 12.2T but apparently not for MPLS for this image).
any way i can get hold of an MPLS image for lab purposes only ?
thanks
Mark
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide