Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

" l2vpn vfi context" not work AT ME3600 (me360x-universalk9-mz.153-2.S.bin)

Somebody knows, Why dont work this vfi, this example is working over ME3600 (PE03) and ASR901 (PE01)

configure router PE03 (10.9.0.175)

interface GigabitEthernet0/12

!

service instance 2561 ethernet

  encapsulation dot1q 2561

  rewrite ingress tag pop 1 symmetric

!

l2vpn vfi context EXAMPLE

vpn id 2561

member 10.9.0.110 encapsulation mpls

member 10.9.0.10 encapsulation mpls

member 10.9.0.80 encapsulation mpls

!

!

bridge-domain 2561

member GigabitEthernet0/12 service-instance 2561

member vfi EXAMPLE

configure router PE01 (10.9.0.80)

!

interface GigabitEthernet0/1

!

service instance 2561 ethernet

  encapsulation dot1q 2561

  rewrite ingress tag pop 1 symmetric

  xconnect 10.9.0.175 2561 encapsulation mpls

!

TSHOOT:

PE01#sh mpls l2transport vc 2561 det

Local interface: Gi0/1 up, line protocol up, Eth VLAN 2561 down

  Destination address: 10.9.0.175, VC ID: 2561, VC status: down

    Last error: Local access circuit is not ready for label advertise

    Output interface: none, imposed label stack {}

    Preferred path: not configured

    Default path: no route

    No adjacency

  Create time: 00:20:44, last status change time: 8w4d

    Last label FSM state change time: 00:20:44

  Signaling protocol: LDP, peer 10.9.0.175:0 up

    Targeted Hello: 10.9.0.80(LDP Id) -> 10.9.0.175, LDP is DOWN, no binding

    Graceful restart: not configured and not enabled

    Non stop routing: not configured and not enabled

    Status TLV support (local/remote)   : enabled/None (no remote binding)

      LDP route watch                   : enabled

      Label/status state machine        : local ready, LruRnd

      Last local dataplane   status rcvd: No fault

      Last BFD dataplane     status rcvd: Not sent

      Last BFD peer monitor  status rcvd: No fault

      Last local AC  circuit status rcvd: No fault

      Last local AC  circuit status sent: Not sent

      Last local PW i/f circ status rcvd: No fault

      Last local LDP TLV     status sent: No fault

      Last remote LDP TLV    status rcvd: None (no remote binding)

      Last remote LDP ADJ    status rcvd: None (no remote binding)

    MPLS VC labels: local 172, remote unassigned

    Group ID: local 0, remote unknown

    MTU: local 1500, remote unknown

    Remote interface description:

  Sequencing: receive disabled, send disabled

  Control Word: On (configured: autosense)

  Dataplane:

    SSM segment/switch IDs: 0/0 (used), PWID: 2

  VC statistics:

    transit packet totals: receive 0, send 0

    transit byte totals:   receive 0, send 0

PE03#sh mpls l2transport vc 2561

Local intf     Local circuit              Dest address    VC ID      Status

-------------  -------------------------- --------------- ---------- ----------

VFI EXAMPLE  vfi                        10.9.0.10     2561       DOWN

VFI EXAMPLE  vfi                        10.9.0.80     2561       DOWN

VFI EXAMPLE  vfi                        10.9.0.110    2561       DOWN

PE03#sh mpls l2transport vc 2561 det

Local interface: VFI EXAMPLE vfi down

  Interworking type is Ethernet

  Destination address: 10.9.0.10, VC ID: 2561, VC status: down

    Last error: Local access circuit is not ready for label advertise

    Output interface: none, imposed label stack {}

    Preferred path: not configured

    Default path: no route

    No adjacency

  Create time: 00:35:05, last status change time: 11w0d

    Last label FSM state change time: 00:35:05

  Signaling protocol: LDP, peer unknown

    Targeted Hello: 10.9.0.175(LDP Id) -> 10.9.0.10, LDP is DOWN, no binding

    Graceful restart: not configured and not enabled

    Non stop routing: not configured and not enabled

    Status TLV support (local/remote)   : enabled/None (no remote binding)

      LDP route watch                   : enabled

      Label/status state machine        : provisioned, LndRnd

      Last local dataplane   status rcvd: No fault

      Last BFD dataplane     status rcvd: Not sent

      Last BFD peer monitor  status rcvd: No fault

      Last local AC  circuit status rcvd: DOWN(hard-down, not-ready)

      Last local AC  circuit status sent: Not sent

      Last local PW i/f circ status rcvd: No fault

      Last local LDP TLV     status sent: No status

      Last remote LDP TLV    status rcvd: None (no remote binding)

      Last remote LDP ADJ    status rcvd: None (no remote binding)

    MPLS VC labels: local unassigned, remote unassigned

    Group ID: local unknown, remote unknown

    MTU: local unknown, remote unknown

    Remote interface description:

  Sequencing: receive disabled, send disabled

  Control Word: Off (configured: autosense)

  Dataplane:

    SSM segment/switch IDs: 0/0 (used), PWID: 24

  VC statistics:

    transit packet totals: receive 0, send 0

    transit byte totals:   receive 0, send 0

    transit packet drops:  receive 0, seq error 0, send 0

Local interface: VFI EXAMPLE vfi down

  Interworking type is Ethernet

  Destination address: 10.9.0.80, VC ID: 2561, VC status: down

    Last error: Local access circuit is not ready for label advertise

    Output interface: none, imposed label stack {}

    Preferred path: not configured

    Default path: no route

    No adjacency

  Create time: 00:35:06, last status change time: 11w0d

    Last label FSM state change time: 00:30:52

  Signaling protocol: LDP, peer 10.9.0.80:0 up

    Targeted Hello: 10.9.0.175(LDP Id) -> 10.9.0.80, LDP is UP

    Graceful restart: not configured and not enabled

    Non stop routing: not configured and not enabled

    Status TLV support (local/remote)   : enabled/supported

      LDP route watch                   : enabled

      Label/status state machine        : remote ready, LndRru

      Last local dataplane   status rcvd: No fault

      Last BFD dataplane     status rcvd: Not sent

      Last BFD peer monitor  status rcvd: No fault

      Last local AC  circuit status rcvd: DOWN(hard-down, not-ready)

      Last local AC  circuit status sent: No fault

      Last local PW i/f circ status rcvd: No fault

      Last local LDP TLV     status sent: No status

      Last remote LDP TLV    status rcvd: No fault

      Last remote LDP ADJ    status rcvd: No fault

    MPLS VC labels: local unassigned, remote 172

    Group ID: local unknown, remote 0

    MTU: local unknown, remote 1500

    Remote interface description: *** SERVICIOS VRFs - SWL3 Gi0/47 ***

  Sequencing: receive disabled, send disabled

  Control Word: Off (configured: autosense)

  Dataplane:

    SSM segment/switch IDs: 0/0 (used), PWID: 25

  VC statistics:

    transit packet totals: receive 0, send 0

    transit byte totals:   receive 0, send 0

    transit packet drops:  receive 0, seq error 0, send 0

Local interface: VFI EXAMPLE vfi down

  Interworking type is Ethernet

  Destination address: 10.9.0.110, VC ID: 2561, VC status: down

    Last error: Local access circuit is not ready for label advertise

    Output interface: none, imposed label stack {}

    Preferred path: not configured

    Default path: no route

    No adjacency

  Create time: 00:35:07, last status change time: 11w0d

    Last label FSM state change time: 00:35:07

  Signaling protocol: LDP, peer 10.9.0.110:0 up

    Targeted Hello: 10.9.0.175(LDP Id) -> 10.9.0.110, LDP is DOWN, no binding

    Graceful restart: not configured and not enabled

    Non stop routing: not configured and not enabled

    Status TLV support (local/remote)   : enabled/None (no remote binding)

      LDP route watch                   : enabled

      Label/status state machine        : ldp ready, LndRnd

      Last local dataplane   status rcvd: No fault

      Last BFD dataplane     status rcvd: Not sent

      Last BFD peer monitor  status rcvd: No fault

      Last local AC  circuit status rcvd: DOWN(hard-down, not-ready)

      Last local AC  circuit status sent: Not sent

      Last local PW i/f circ status rcvd: No fault

      Last local LDP TLV     status sent: No status

      Last remote LDP TLV    status rcvd: None (no remote binding)

      Last remote LDP ADJ    status rcvd: None (no remote binding)

    MPLS VC labels: local unassigned, remote unassigned

    Group ID: local unknown, remote unknown

    MTU: local unknown, remote unknown

    Remote interface description:

  Sequencing: receive disabled, send disabled

  Control Word: Off (configured: autosense)

  Dataplane:

    SSM segment/switch IDs: 0/0 (used), PWID: 23

  VC statistics:

    transit packet totals: receive 0, send 0

    transit byte totals:   receive 0, send 0

    transit packet drops:  receive 0, seq error 0, send 0

2 REPLIES
New Member

" l2vpn vfi context" not work AT ME3600 (me360x-universalk9-mz.1

Have you tried, including the BD under the service-instance?

!

service instance 2561 ethernet

  encapsulation dot1q 2561

  rewrite ingress tag pop 1 symmetric

   bridge-domain 2561 <<<<

!

New Member

Re: " l2vpn vfi context" not work AT ME3600 (me360x-universalk9-

if you configure de BD into service instance you can't configure the BD with vfi members

this is the error message:

%The service instance is already a member of bridge-domain 2561

1340
Views
0
Helpful
2
Replies
CreatePlease login to create content