Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Sup720-3B - not showing to support MPLS / LDP

I have a Sup720-3B- it is using the same version of code as my other 6500 series switches that are supporting LDP/MPLS.  Here is the sh mod:

 

Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAD08290FLG
  2   16  16 port 1000mb GBIC ethernet           WS-X6416-GBIC      SAD04240LDR
  3   16  16 port 1000mb GBIC ethernet           WS-X6416-GBIC      SAD041406L9
  4   48  48-port 10/100/1000 RJ45 EtherModule   WS-X6148A-GE-TX    SAL09507UST
  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL1208GTEL

Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  1  0011.9210.1774 to 0011.9210.178b   2.1   12.2(18r)S1  12.2(33)SXI1 Ok
  2  00d0.d3a4.c5dd to 00d0.d3a4.c5ec   1.1   5.3(1)       12.2(33)SXI1 Ok
  3  0030.19d8.59c8 to 0030.19d8.59d7   1.1   5.3(1)       12.2(33)SXI1 Ok
  4  0016.4778.7600 to 0016.4778.762f   1.1   8.4(1)       12.2(33)SXI1 Ok
  5  0016.c848.3880 to 0016.c848.3883   5.6   8.5(2)       12.2(33)SXI1 Ok

Mod  Sub-Module                  Model              Serial       Hw     Status 
---- --------------------------- ------------------ ----------- ------- -------
  1  Distributed Forwarding Card WS-F6700-DFC3A     SAL08290N34  2.2    Ok
  5  Policy Feature Card 3       WS-F6K-PFC3B       SAL1208GUY6  2.3    Ok
  5  MSFC3 Daughterboard         WS-SUP720          SAL1208GSV6  3.1    Ok

Mod  Online Diag Status 
---- -------------------
  1  Pass
  2  Pass
  3  Pass
  4  Pass
  5  Pass

 

and the code version:

 

Uptime for this control processor is 5 days, 19 hours, 50 minutes
Time since Br03-CORE-6506-1 switched to active is 5 days, 19 hours, 49 minutes
System returned to ROM by  power cycle at 15:33:41 UTC Wed Apr 30 2014 (SP by power on)
System restarted at 16:03:27 CDT Tue Jun 10 2014
System image file is "sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI13.bin"
Last reload reason: reload

 

for some reason it's not supporting "mpls label protocol ldp"

 

any ideas?

 

Thanks

Greg

 

 

Everyone's tags (4)
2 REPLIES
Cisco Employee

Greg,MPLS is supported in

Greg,

MPLS is supported in SUP720-3B. Please check the below datasheet,

 

http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/product_data_sheet09186a0080159856.html

 

Can you share the error you are getting while tryign to configure the command?. Were you able to enable mpls ip under interfaces?.

 

--Nagendra

Cisco Employee

I believe the reason is that

I believe the reason is that your have WS-F6700-DFC3A on LC1 and my guess is system is falling into PFC3A mode.

Please see Table 1. DFC3 Supported Combinations on link below

http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/prod_bulletin0900aecd8017a5db.html

Can you please collect the output of "show platform hardware pfc mode"

Best Regards,

Bheem

170
Views
0
Helpful
2
Replies
CreatePlease to create content