Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

6506-e - RME Error

While trying to pull config for a 6506e get this error:CM0056 Config fetch failed for g0ghq3esw1 Cause: CM0204 Could not create DeviceContext for 17118 Cause: CM0206 Could not get the config transport implementation for 10.160.8.29 Cause: UNKNOWN Action: Check if required device packages are available in RME. Action: Check if protocol is supported by device and required device package is installed.

What updates do I need?

15 REPLIES
Cisco Employee

Re: 6506-e - RME Error

What is the sysObjectID from this device? You can find that under Device Center > SNMP Walk. Just walk sysObjectID.

New Member

Re: 6506-e - RME Error

I just noticed that no configs for my 6504-e's are pulling. What updates do I need to to for CW to pull.

CM 4.0

DFM 2.0

IPM 2.6

RME 4.0

If updates are required, what order are they to be installed?

Cisco Employee

Re: 6506-e - RME Error

These are not complete versions. What is the exact version of RME you have, plus, what is the sysObjectID of this switch?

New Member

Re: 6506-e - RME Error

RME - 4.0.5

SysObjectID - RFC1213-MIB::sysObjectID.0 = OID: CISCO-SMI::ciscoProducts.657

Cisco Employee

Re: 6506-e - RME Error

Support for this switch is available in Cat6000IOS package version 6.1. This package can be downloaded via the Common Services > Software Center > Device Update interface.

New Member

Re: 6506-e - RME Error

While installing CAT6000ios GOT this error:

Cat6000IOS

WARNING : Cat6000IOS(6.1):Consistency check failed for base package SharedInventoryCatIOS

ERROR: Error while installing (SharedNetshowSC): D:appsCSCOpx emppsuinstall

meSharedNetshowSC.zip cannot be installed because, the current mdf version:1.12 is LESS THAN the minimum required mdf version:1.16

Where do I fin MDF 1.16?

Cisco Employee

Re: 6506-e - RME Error

The MDF is found by selecting Common Services in addition to RME when performing the Device Update. Select all available updates.

New Member

Re: 6506-e - RME Error

For Product(s) : Resource Manager Essentials

Install Invoked by user : admin

The Package(s) Selected for Install :

I installed MDF update and still get this message while trying to install CAT6000IOS package:

LibCommon

ERROR: Error while installing (LibCommon): C:psu_download

meLibCommon.zip cannot be installed because, the current mdf version:1.12 is LESS THAN the minimum required mdf version:1.19

Cisco Employee

Re: 6506-e - RME Error

You must not have installed the MDF correctly. The current latest version is 1.21. This time, select just Common Services, pick the MDF 1.21 update, and install it. That should prompt a daemon restart. When you're able to login again, then install the RME updates.

New Member

Re: 6506-e - RME Error

When I select Common Services and go get the download I get :

All the available package(s) at source location are already installed.

Dosen't this mean that the current MDF is already installed?>

Cisco Employee

Re: 6506-e - RME Error

If you click on the CiscoWorks Common Services link under Device Update, what do you see?

New Member

Re: 6506-e - RME Error

I select Common Services,

I click "Check for Updates"

I get the source location display,

I select Cisco.com,

I enter my CCO info,

I click next, then I get :

All the available package(s) at source location are already installed.

Cisco Employee

Re: 6506-e - RME Error

No, just click the hyperlink "CiscoWorks Common Services" under Common Services > Software Center > Device Update.

New Member

Re: 6506-e - RME Error

Package Map

Filter Source: Package Name Version

Showing 1-1 of 1 records

Package Name Version Description

1. Mdf 1.12 MDF Package

Cisco Employee

Re: 6506-e - RME Error

Try restarting dmgtd, then see if the MDF version changes (assuming it was able to apply from one of your previous attempts). If not, you will need to download the MDF 1.21 update manually from http://www.cisco.com/cgi-bin/tablebuild.pl/cw2000-cd-one , then install it using NMSROOT\bin\PSUCli.bat.

193
Views
0
Helpful
15
Replies
CreatePlease login to create content