Dear All,we have configured LMS to send emails when Interface Utilization is higher than 40% (default Threshold).The mails look like this:EVENT ID = 00012QSTIME = Wed 07-Nov-2012 03:03:54 CETSTATUS = Ac...
Dear All,we have configured LMS to send emails when Interface Utilization is higher than 40% (default Threshold).The mails look like this:EVENT ID = 00012QSTIME = Wed 07-Nov-2012 03:03:54 CETSTATUS = Ac...
Hi All,Just a general question really; I have attempted to Google it & look through these forums but coun't see anything - not sure if its my poor wording of the search term??I have created a baseline template to run compliancy checks, I understand t...
Guys,I have a C3560 (C3560-HBOOT-M) Version 12.2(25r)SE1, RELEASE SOFTWAREMODEL WS-C3560G-24TS-SWould it be possibel to configure netflow on this device.I don't see any ip route-cache flow command.Looking forward to your answers.Nik
Hi,I'm trying to get via snmp the next-hop address of the default route or the interface via it's known.Before It got deprecated, I used .1.3.6.1.2.1.4.21.1.7.0.0.0.0 (ipRouteNextHop). It returned the next-hop address of the 0.0.0.0, in this case.Now...
I just installed CiscoWroks 4.0 LMS on this network and I'm conducting an initial discoveryThe SNMP community settings for the devices are all correct, but when I do my discovery, CiscoWorks discovers the devices, but saysDevices newly added to DCR: ...
Hi everyone,I have a Question, Can I change interface Vlan ID from the CiscoView?for example I want to change interface G1/1/1 in Vlan 1 to Vlan 2 from CiscoView?thanks
Hi All,In VPN 3000 concerntrator, I've enabled tftp, telnet, snmp. I've also successfully added the concerntrator into Ciscoworks LMS 4.2.2. All the ports are verified open to Ciscoworks. No question mark shows next to this device in the device manag...
Does the script need to be tied to a TTY / COnsole session or can a command be invoked to run the script, log off and still have the script running?
Hi everybody,I need the part number/configuration of 1 unit of Cisco ACE (Application Control Engine) 4710 Appliance using the details below.Software loader: Version 0.95.1 system: Version A3(2.7) [build 3.0(0)A3(2.7) adbui...
Hi Everyone,I've a strange problem with LMS CiscoView I can't see ONE (its stack of two) device in the CiscoView.and im getting an error mesg'The LMS is connected to ACS and all the I.T Department can't see this specific device in CiscoViewI've tried...
I have applied the following eem policy to backup our switch config when a change is made to the configuration:event manager applet SAVE event syslog occurs 1 pattern "%SYS-5-CONFIG_I:" action 1.0 cli command "enable" action 2.0 cli command "copy ru...
Hello All,I would need your help about the following :let's say that I have a file stored on "disk0a:/usr/" and it's name is "_debug.dat"and I want to transfer that file using SSH to home directory "nikos" on the server "1.1.1.1" and the password wou...
HiI have installed Cisco Works LMS 3.2.If I go to Campus Manage - Visualization - Topology service, I couldnt see the topolgy.First time it was asking install java. After install Java it is not work. Again and again it is asking install java and the ...
The DFM 3.1.3 was not oppening the Alerts and Activities, then I had removed it and reinstalled DFM 3.1.0.After the reinstallation I got error pointing to the AAD.log. The Alerts and Activities now open empty, thats OK, but when I...
Hi,I have a problem with LMS 4.2, I had a lot of problem with databases who's growing, fault not true, and many others. So when i managed the database and others, i wanted to delete all the devices in Inventory,and i rediscovered t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-25-2024 01:17 PM | ||
04-25-2024 08:57 AM | ||
04-23-2024 05:52 PM | ||
04-23-2024 12:20 AM | ||
04-16-2024 04:45 AM |
User | Count |
---|---|
3 | |
2 | |
2 | |
2 | |
1 |