Hello!I have 4 switches of 3750. I need toupgrade all the switches, but I can't to disconnect the stack cable.How I can to upgrade the version without to disconnect the stack cable?Sent from Cisco Technical Support iPhone App
Router#cellular 0/0/0 cdma activate otasp *228Beginning OTASP activationOTASP number is *228.After execution of "cellular 0/0/0 cdma activate otasp *228" on the global prompt of the router... will see output “OTASP number is *228.” Log on the consol...
Hi all.Hope i can get some help as i am quite noive in Cisco and still learning.I am tasked with configuring an AP as a repeater.I have reset the AP to defaults and configured it in CLI with the below:configure terminalinterface dot11radio 0ssid JDC-...
Hi,LMS 4.2.3The syslog automated action work if we send to one e-mail address the messages.Once we set two email-adresses ( comma separeted ) in "send to field", the messages are not received.Thanks
HelloI am trying to setup netflow with on 6509 and SolarWinds NetFlow Traffic Analyzer v3.10.0The problem I have is that after configuring the basic settings of NetFlow on both side I can't see all the traffic I expected to capture in NetFlow.The det...
Hello,I have a problem with LMS 4.2 user tracking.When I generate a report on all my network all mac address are ok but there is no Hostname/Ip address in the result, except for 2 equipments.the only difference between these 2 equipements and the res...
Hi,I have a Cisco Prime LMS 4.1 running on my network, and I am creating Jobs to configure access-list, snmp commands. I can make ping/telnet/ssh from Cisco Prime LMS CLI to the devices (routers or switches), but when a Job is scheduled it fails. Wha...
Hello,we are running LMS 4.1 on a virtual machine (Windows Server 2008 R2 Standard Edition ). After regional time change, the time on the virtual machine seems to be automatically updated. But the time on the LMS application still shows the old value...
Hello, I wanted get erros for an interface by gets snmps from a external software. for exemplo, from Linux machine I'm able type snmpwalk -c public -v 1 ip_of_my_switchso it's return all OID avaliable for that device. what I wish is find out what is ...
Hello supportforum memebers,Does anybody know what hardware in the NCS appliance (http://www.cisco.com/en/US/products/ps11686/index.html) exist?What CPU / RAM / HDD / ...?Thanks Sebastian
Hi all Could you please say me if it is possible to install both LMS & DCNM on the same physical server ? I guess some ports are shared by both applications (SNMP...) but it may be possible if we don't want to use the same services (basically we woul...
Hi All,Got to know from my colleague that below IOS and MIB are running on modular IOS (VZ image), hence, the SNMP objects ciscoMemoryPoolUsed and ciscoMemoryPoolFree report specifically on the 'ios-base' statistics as is seen in the output of "show ...
good morning,I hope that you help me, i need to save the configuration of my firewalls and routers in a server (any service suggested for you, preference opensource). for example, if i write a new access-list in my firewalls, my config file on my ser...
HelloI'm having some problems with PRI monitoring.I'm using cpmDS1ActiveDS0 MIB on a 3800 VoIP gateway with 4 PRI (2x2) (IOS 12.4(4)T1)1.3.6.1.4.1.9.10.19.1.1.9.1.3.0.0 - I can see PRI 0/0/0 total number of calls1.3.6.1.4.1.9.10.19.1.1.9.1.3.0.1 - I ...
How monitor multiple dial-peer (Connect Time) ??When this reaches the defined time accumulated connected (example: Connect Time = 10000) shutdown the dial-peer.UC520#show dial-peer voice 2 | beg ConnectConnect Time = 1430, Charged Units = 0,Successfu...
