Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Caclculate VoIP metrics using SAA/rttMon

Hi,

Please can somebody help me with calculating the VoIP parameters jitter,delay,packet loss using rttMon MIB.It gives lots of OID's .But I am not clear enough to pick up which one.

Thanks in advance for the help

4 REPLIES

Re: Caclculate VoIP metrics using SAA/rttMon

Hi, I downloaded a sample MRTG script ages ago and tested it on some Catalyst 3550's & 3560's using ip sla (saa). The OID's in the script were:

jitter .1.3.6.1.4.1.9.9.42.1.5.2.1.7.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.17.1

RTT .1.3.6.1.4.1.9.9.42.1.5.2.1.2.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.2.1 & .1.3.6.1.4.1.9.9.42.1.5.2.1.1.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.1.1

Packet loss .1.3.6.1.4.1.9.9.42.1.5.2.1.26.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.27.1

I apologise for my lack of SNMP knowledge in advance....

HTH

Andy

New Member

Re: Caclculate VoIP metrics using SAA/rttMon

Hi,

Thanks for the information.Actually I am also new to this field of Network Management.I am drilling through the OIDs but not getting exactly what to pick up...I am picking up the oids from the rttMonLatestJitter table.

I tried the oids you mentioned.Only the thing is the end .1 which u specified for evry oid it shows no mib information when i query.help me on that to understand

Thanks for the help

Re: Caclculate VoIP metrics using SAA/rttMon

Hi, as I said apologies for my lack of SNMP knowledge. I can post the MRTG script I used however there isn't much more in it apart from the values to graph:

# SAA POS JITTER

Target[test-saa-posjitter]: .1.3.6.1.4.1.9.9.42.1.5.2.1.7.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.17.1:public@192.168.255.254

Maxbytes[test-saa-posjitter]: 10000

Title[test-saa-posjitter]: SAA MAX Positive jitter

PageTop[test-saa-posjitter]:

SAA MAX Positive jitter

ShortLegend[test-saa-posjitter]: ms

YLegend[test-saa-posjitter]: miliseconds

Legend1[test-saa-posjitter]: MAX Positive jitter SD

Legend2[test-saa-posjitter]: MAX Positive jitter DS

LegendI[test-saa-posjitter]: SD:

LegendO[test-saa-posjitter]: DS:

Options[test-saa-posjitter]: growright, gauge, nopercent

# SAA NEG JITTER

Target[test-saa-negjitter]: .1.3.6.1.4.1.9.9.42.1.5.2.1.7.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.17.1:public@192.168.255.254

Maxbytes[test-saa-negjitter]: 10000

Title[test-saa-negjitter]: SAA MAX Negative jitter

PageTop[test-saa-negjitter]:

SAA MAX Negative jitter

ShortLegend[test-saa-negjitter]: ms

YLegend[test-saa-negjitter]: miliseconds

Legend1[test-saa-negjitter]: MAX Negative jitter SD

Legend2[test-saa-negjitter]: MAX Negative jitter DS

LegendI[test-saa-negjitter]: SD:

LegendO[test-saa-negjitter]: DS:

Options[test-saa-negjitter]: growright, gauge, nopercent

# SAA RTT

Target[test-saa-rtt]: .1.3.6.1.4.1.9.9.42.1.5.2.1.2.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.2.1:public@192.168.255.254 / .1.3.6.1.4.1.9.9.42.1.5.2.1.1.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.1.1:public@192.168.255.254

Maxbytes[test-saa-rtt]: 10000

Title[test-saa-rtt]: SAA RTT

PageTop[test-saa-rtt]:

SAA RTT

ShortLegend[test-saa-rtt]: ms

YLegend[test-saa-rtt]: miliseconds

Legend1[test-saa-rtt]: Latest RTT

Legend2[test-saa-rtt]: Latest RTT

LegendI[test-saa-rtt]: RTT:

LegendO[test-saa-rtt]: RTT:

Options[test-saa-rtt]: growright, gauge, nopercent

# SAA Packet loss

Target[test-saa-pktloss]: .1.3.6.1.4.1.9.9.42.1.5.2.1.26.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.27.1:public@192.168.255.254

Maxbytes[test-saa-pktloss]: 10000

Title[test-saa-pktloss]: SAA Packet loss

PageTop[test-saa-pktloss]:

SAA Packet loss

ShortLegend[test-saa-pktloss]: pkts

YLegend[test-saa-pktloss]: Packets

Legend1[test-saa-pktloss]: Packet loss SD

Legend2[test-saa-pktloss]: Packet loss DS

LegendI[test-saa-pktloss]: SD:

LegendO[test-saa-pktloss]: DS:

Options[test-saa-pktloss]: growright, gauge

Hopefully someone with more a bit more of a clue than me will reply....

Andy

New Member

Re: Caclculate VoIP metrics using SAA/rttMon

Thanks Sir,

That will help me to understand.I will get back to you if I find any difficulty.

Thanks again for help,

Shivani

229
Views
0
Helpful
4
Replies