Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Ciscoworks Lms 3.2 giving ANi Server issue

We have lms 3.2 configured at our organisation.But i am not able to initialise ANI server.The process is always down and not coming up.

EDS and anidatabase processes are up.But ani server is not coming up due to which i am not able to access the CAmpus manager.Please reply asap.

15 REPLIES
Cisco Employee

Re: Ciscoworks Lms 3.2 giving ANi Server issue

Post the output of the pdshow command from the server as well as the ani.log and ANIServer.log.

--

Please support CSC Helps Haiti

https://supportforums.cisco.com/docs/DOC-8895

https://supportforums.cisco.com

New Member

Re: Ciscoworks Lms 3.2 giving ANi Server issue

The following is the output as an attachment.

Cisco Employee

Re: Ciscoworks Lms 3.2 giving ANi Server issue

Post the NMSROOT/campus/etc/cwsi/ANIServer.properties.

New Member

Re: Ciscoworks Lms 3.2 giving ANi Server issue

Before this below was the output then i followed one doc im attaching  it now and changed as per the instructions.Il paste the current files also.

EnablePurgeArchives=ON
PurgeArchivesOlderThan=180
EnablePurgeJobs=ON
PurgeJobsOlderThan=180
EnableCMPurgeArchives=ON

I have attached the doc which i followed to change the aniserver file but still did not initialise the aniserver.

Aniserver issue .pdf is the file i followed to change the corrupted aniserver file.

aniserver.properties is the file attached with current settings after changing.

Cisco Employee

Re: Ciscoworks Lms 3.2 giving ANi Server issue

These properties were not the problem.  You had messed up the module path.  Replace your version with this attached one.  Then restart Daemon Manager, and you should be good to go.

--

Please support CSC Helps Haiti

https://supportforums.cisco.com/docs/DOC-8895

https://supportforums.cisco.com

New Member

Re: Ciscoworks Lms 3.2 giving ANi Server issue

I have followed the steps and restored the configs but still ani server is down.Please advise

Cisco Employee

Re: Ciscoworks Lms 3.2 giving ANi Server issue

Post the new pdshow output, ani.log, and ANIServer.log.  Repost the ANIServer.properties that you now have in NMSROOT/campus/etc/cwsi.

New Member

Re: Ciscoworks Lms 3.2 giving ANi Server issue

Here are the attachments.

Cisco Employee

Re: Ciscoworks Lms 3.2 giving ANi Server issue

Try this version.

New Member

Re: Ciscoworks Lms 3.2 giving ANi Server issue

Thankyou the Ani Server is up but it is running with busy flagset.The other thing is the Discrepencies reports and violations report is not  showing anything.

The respone time of the server is ver y slow

Cisco Employee

Re: Ciscoworks Lms 3.2 giving ANi Server issue

Running with busy flag set is the normal state for ANIServer.  See my Daemon Cheat Sheet at https://supportforums.cisco.com/docs/DOC-8798 for more on what the healthy daemon states should be.

The Discrepancies and BPD will only be populated after a Campus Data Collection is run.  It can take up to 30 minutes after a restart of Daemon Manager before the daemons calm down, and the system becomes responsive.

New Member

Re: Ciscoworks Lms 3.2 giving ANi Server issue

Thankyou very much ,The Campus Manager lists are populated again.One more thing i wanted to Know regarding MS Tcp loopback Interface.My Management software is showing high utilization on this MS tcp loopback interface of 10 mb on Cisco works Server.

Cisco Employee

Re: Ciscoworks Lms 3.2 giving ANi Server issue

LMS does a lot of internal communication (i.e. inter-process communication) on 127.0.0.1.  Therefore, it would not be uncommon for one to see high loopback traffic.

--

Please support CSC Helps Haiti

https://supportforums.cisco.com/docs/DOC-8895

https://supportforums.cisco.com

New Member

Ciscoworks Lms 3.2 giving ANi Server issue

hi Joseph,

recently I have faced the same issue and after changing the properties file ANI server started but now i am getting the error "There may be possible ACS config mismatch " where as i have not changed the ACS settings. Could u pls help me out .

Cisco Employee

Ciscoworks Lms 3.2 giving ANi Server issue

Hey, Arun.  Please start a new for your issue.  With ACS integration, you need to make sure all of the ACS side settings are good.  While you may not have changed anything within LMS, the ACS side may have changed.  For example, an ACS admin may have deleted some of the LMS components in ACS, or ACS may have been upgraded to an unsupported version (e.g., 5.x).

1545
Views
9
Helpful
15
Replies