I installed the SDM, and i did configure it and the wholething... just i have a problem... once i restart the cisco router... it ask me this question: "Would you like to enter the initial configuration dialog? [yes/no]:"
And each time i restart it i have to configure it at all... is there any way to save the config the boot paramethers or some like that?
(note: of course i saved the config and i did the copy running conf to start up conf..)
For details i will include here the whole console message
------------------------------------------------------
Copyright (c) 2005 by cisco Systems, Inc.o find computer address to
Testing lower main memory - data equals addressN:
Router>show versionistratively downate
Cisco
Testing lower main memory - checkerboardURITYK9-M), Version 12.3(8)YI2, RE2, cha
Testing lower main memory - inverse checkerboard1(config-if)#no ip addres
LEASE SOFTWARE (fc1)ad
Clearing lower 16K memory for cache initialization.3(10.3)T29: %LINK-5-CHANGED: Interface FastEthern
Clearing bssSupport: htt
Initializing FlashechsupportEPROT
Fi
Reading monitor variables f
ROUTE
et0, changed state to downssK9-M), Ver
2,
Booting flash:/c870-advsecurityk9-mz.123-8.YI2.binter uptime is 1 minuteerface FastEthernico1(con
Sy
Self decompressing the image : #################################################ile is "flash:c870-advsecurityk9-mz.123-8.YI2.bin"00:00:46.599: %LINEPROTO-5-UPD
############## [OK]n Interface Fa
Th
Restricted Rights Legendes and is subject to UnitedO-5-UPDOWN:
Use, duplication, or disclosure by the Government isght
States and local country laws governing import,
subject to restrictions as set forth in suin
Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.3(8)YI2, REws, return this product immediately.0.319: %SNMP-5-COLDSTART: SNMP agent on host
LEASE SOFTWARE (fc1)eb
A summary of U.
Synched to technology version 12.3(10.3)T2cts may be found at:g a cold start16148 bl
Technical Support: »www.cisco.com/techsupportn't
Changing crypto engine : Onboard: 0 state change to: INIT00) with 118784K/12288K bytes of memostems, Inc.s
ROUTERNAME
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
»www.cisco.com/wwl/export/crypto/···qrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 871 (MPC8272) processor (revision 0x100) with 118784K/12288K bytes of memo
ry.
Processor board ID FHK094812MQ
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
5 FastEthernet interfaces
128K bytes of non-volatile configuration memory.
28672K bytes of processor board System flash (Intel Strataflash)
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]:
---------------------------------------------------
also i tried doing this:
copy running-config startup-config
also
copy system:running-config nvram:startup-config
and each time i turnoff and turn on the router it boot up with a blank configuration and ask for the "Would you like to enter the initial configuration dialog? [yes/no]:" each time... is frustrating...
