Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Icmp Jitter collector configuration with Cisco LMS

Hi,

I am trying to collect jitter information of cisco Routers which are added in Cisco LMS

 

I have configured collector icmp jitter for them but somehow no stats are visible in lms and its says in IPM that u have no jitter collectors configured.

 

Do i need to enable anything on the Router as well to export stats to LMS ?

 

Thanks

Everyone's tags (1)
19 REPLIES
Cisco Employee

Hi,can you share the screen

Hi,

can you share the screen shot of the collector that you have created ?

did you check  and find any IPSLA config on the device after configuring the IPSLA collector ?

 

Thanks-

Afroz

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

Hi,  Thanks for the reply . I

Hi, 

 

Thanks for the reply .

 

I have configured icmp collector through GUI in cisco LMS

and for the router i have enable ip sla for icmp jitter

config of Router is :

ip sla 1
 icmp-jitter 10.80.10.55 source-ip 10.11.0.89 num-packets 100 interval 40
 frequency 50
ip sla reaction-configuration 1 react jitterAvg threshold-value 5 2 threshold-type immediate action-type trapOnly
ip sla schedule 1 life forever start-time now
logging 192.128.10.20
snmp-server view default iso.0.8802 included
snmp-server view default iso.1.2 included
snmp-server view default org.111 included
snmp-server view default internet included
snmp-server community abcd RO
snmp-server community efgh RW
snmp-server community public view default RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server host 192.128.10.20 abcd

Apart from this do i need to configure anything else on Router ?

 

 

Cisco Employee

Hi , No more configuration is

Hi ,

 

No more configuration is needed. 

first  define the Operations and then create the collector.

go to Internetwork Performance Monitor > Collector Management > Collectors.

 

http://www.cisco.com/c/en/us/td/docs/net_mgmt/ciscoworks_internetwork_performance_monitor/4-2/user/guide/IPM4_2ug/ipmopmg.html

http://www.cisco.com/c/en/us/td/docs/net_mgmt/ciscoworks_internetwork_performance_monitor/4-2/user/guide/IPM4_2ug/ipmclmg.html

 

select your collector and click view  , share the screen shot for the same.

 

Thanks-

Afroz

***Ratings Encourages Contributors ***

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

Hi,Pls see atached file , is

Hi,

Pls see atached file , is there a problem with the responder detail marked as false ?

Cisco Employee

Hi, for ICMP jitter operation

Hi,

 

for ICMP jitter operation ,configuring responder is not required.

Are you facing issue with only this device or all of them ?

 

what is the output of the below command on your device :

"show ip sla monitor application"
OR
"show ip sla application"

 

Is IPSLA is supported on this device ?

and " show license"

share the above outputs

 

Thanks-

Afroz

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

Hi, show ip sla application 

Hi,

 

show ip sla application
        IP Service Level Agreements
Version: Round Trip Time MIB 2.2.0, Infrastructure Engine-II
Time of last change in whole IP SLAs: *07:35:21.730 UTC Thu Mar 13 2014
Estimated system max number of entries: 27977

Estimated number of configurable operations: 27976
Number of Entries configured  : 1
Number of active Entries      : 1
Number of pending Entries     : 0
Number of inactive Entries    : 0

        Supported Operation Types
Type of Operation to Perform: dhcp
Type of Operation to Perform: dns
Type of Operation to Perform: echo
Type of Operation to Perform: frameRelay
Type of Operation to Perform: ftp
Type of Operation to Perform: http
Type of Operation to Perform: icmpJitter
Type of Operation to Perform: jitter
Type of Operation to Perform: pathEcho
Type of Operation to Perform: pathJitter
Type of Operation to Perform: slm controller
Type of Operation to Perform: slm frame-relay interface
Type of Operation to Perform: slm frame-relay pvc
Type of Operation to Perform: slm interface
Type of Operation to Perform: tcpConnect
Type of Operation to Perform: udpEcho
Type of Operation to Perform: voip

IP SLAs low memory water mark: 38288719

 

The device is a Cisco 1841 

Cisco Employee

Hi,Thanks for sharing it..

Hi,

Thanks for sharing it.. devices side it should not be a problem.

 

Is your devices managed properly , I mean inventory and configuruation backup >they are sucessfull.

If everything is fine then try to delete the existing  opeartion and collector and re-configure (operation >>collector).

 

Thanks-

Afroz

 

 

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

 Still not working .. the

 

Still not working .. the device is accessible from LMS , aso i configured / reconfgured but still no success

Cisco Employee

 can share the CDA job result

 

can share the CDA job result  of that device. { Inventory > Job Browsers > Device Credentials Verification}

 

Thanks-

Afroz

 

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

Hi,Thanks for all ur help ,

Hi,

Thanks for all ur help , pls refer attachment

Cisco Employee

by mistake you have attached

by mistake you have attached a wrong screen shot , I need the job result of device credentilas verification  of this device  [Inventory > Job Browsers > Device Credentials Verification].

 

Thanks-
 

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

Sorry for the inconvenience

Sorry for the inconvenience.

Is the attached sc sufficeint ? 

Cisco Employee

you are using LMS ?what is 

you are using LMS ?

what is  the version of LMS you are using ?

 

still it is an incorrect screen shot.

 

what I see in your shared screenshot  , I have attached the same  for you ..

 

Thanks-

Afroz

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

This is really strange , on

This is really strange , on both occasions i have attached a screenshot displaying snmp read write change and successful exchange of LMS with the device.

I am using Cisco Lms 3.1

reattaching

Cisco Employee

LMS 3.1 is very old. I would

LMS 3.1 is very old.

 

I would suggest you to upgarde the LMS to 3.2.1 as there were few known issue in LMS 3.1

 

Thanks-

Afroz

***Ratings Encourages Contributors **

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

 So ICMP Jitter Collectors

 

So ICMP Jitter Collectors wont work with 3.1 ?

Cisco Employee

HI , You are running a

HI ,

 

You are running a version which already end of support.

 

Atleast  upgarde it to 3.2.1 and which was most stable version of LMS with a lot of enhancment with respect to IPM

---

in the meantime check the below output and see if you are able to see the result of the operations in it:

show ip sla statistics

 

Thanks-

Afroz

***Ratings Encourages Contributors ***

 

 

 

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
Cisco Employee

One quick thing : you are

One quick thing :

 

you are using SNMP v2 or SNMPv3 on your devices ?

 

***IMP >> you need to have  SNMP RW credentials added in LMS for IPSLA to work for any device.

 

Thanks-

Afroz

**Ratings Encourages Contributors ***

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

Hi, I am using snmp V2 with

Hi,

 

I am using snmp V2 with both RW and WR credentials , still not working though

347
Views
5
Helpful
19
Replies