Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

inventory change details only with 4500

The inventory change details show me hardware and software changes that not happened only with 4500 series.

9 REPLIES
Cisco Employee

Re: inventory change details only with 4500

What 4500 is this (i.e. a router or the Cat4500)? What version of RME are you using? Specifically what changes are being reported?

Community Member

Re: inventory change details only with 4500

RME version 4.0.3

Devices afected:

WS-C4510R - IOS 12.2

WS-C4506 - IOS 12.2

WS-C4507R - IOS 12.2

piece of the report:

Changes for Device: 45A10

Chassis Identity: ChassisID = 1

Attribute Type of Change Time Change Detected Previous Value Current Value

Free Slots Changed 2007-04-30 03:02:23.953 2 1

Cisco Employee

Re: inventory change details only with 4500

According to this, the number of free module slots decreased by one. Please provide a show mod from this 45A10 switch. There should only be one free module slot.

Community Member

Re: inventory change details only with 4500

------------------ show module ------------------

Chassis Type : WS-C4510R

Power consumed by backplane : 40 Watts

Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 2 Supervisor V 1000BaseX (GBIC) WS-X4516 JAE0946Q2AG

2 2 Supervisor V 1000BaseX (GBIC) WS-X4516 JAE0952SKDE

3 6 1000BaseX (GBIC) WS-X4306-GB JAE0948R2C0

4 6 1000BaseX (GBIC) WS-X4306-GB JAE0948R362

5 6 1000BaseX (GBIC) WS-X4306-GB JAE0948R28H

6 6 1000BaseX (GBIC) WS-X4306-GB JAE0948R34K

7 6 1000BaseX (GBIC) WS-X4306-GB JAE0948R39J

8 6 1000BaseX (GBIC) WS-X4306-GB JAE0950RJCX

9 48 10/100BaseTX (RJ45) WS-X4148-RJ JAE063505D0

M MAC addresses Hw Fw Sw Status

--+--------------------------------+---+------------+----------------+---------

1 0016.4778.3c80 to 0016.4778.3c81 3.0 12.2(20r)EW1 12.2(25)EWA5 Ok

2 0016.4778.3c82 to 0016.4778.3c83 3.0 12.2(20r)EW1 12.2(25)EWA5, Ok

3 0015.630c.505a to 0015.630c.505f 4.1 Ok

4 0015.630c.510e to 0015.630c.5113 4.1 Ok

5 0015.630c.4ba4 to 0015.630c.4ba9 4.1 Ok

6 0015.630c.50de to 0015.630c.50e3 4.1 Ok

7 0015.630c.50f6 to 0015.630c.50fb 4.1 Ok

8 0015.630c.5882 to 0015.630c.5887 4.1 Ok

9 000a.b7c9.0fc0 to 000a.b7c9.0fef 3.1 Ok

Mod Redundancy role Redundancy mode Redundancy status

----+-------------------+-------------------+-------------------

1 Active Supervisor SSO Active

2 Standby Supervisor SSO Standby hot

Cisco Employee

Re: inventory change details only with 4500

The inventory change in RME is correct. This switch only has one free module. At some point, someone must have inserted a new module thus reducing the available module count from 2 to 1.

Community Member

Re: inventory change details only with 4500

What do you think about this peace of the report to the same device (45a10).

Module Identity: ModuleID = 3000

Attribute Type of Change Time Change Detected Previous Value Current Value

HW Version Changed 2007-04-30 03:02:23.953 V09 nc??ı??ı V09 nc??ı??ı

Module Identity: ModuleID = 4000

Attribute Type of Change Time Change Detected Previous Value Current Value

HW Version Changed 2007-04-30 03:02:23.953 V09 nc??ı??ı V09 nc??ı??ı

Cisco Employee

Re: inventory change details only with 4500

The data appears unreadable in my browser. However, given the type of change, it appears that these modules were either upgraded or switched around in the chassis. Without more details as to what was physically done to this device, it's hard to say.

Community Member

Re: inventory change details only with 4500

Yes, I know. Thank you for your replies, I just want you, one more think, where can I found a doc. about these information on inventory change details report.

thank you again.

Cisco Employee

Re: inventory change details only with 4500

All of the various inventory attributes and their descriptions are listed at http://server/help/rme/fundamentals/invent_ChangeReportFltrs.html#wp1139605 in the online help. You can also disable the tracking of changes for attributes you do not care about under RME > Admin > Inventory > Inventory Change Filter.

287
Views
13
Helpful
9
Replies
CreatePlease to create content