Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Is there a way to determine the OID's for specific show commands ? I'm LOST

PEE_VOICE_2#sh voice call status

CallID CID ccVdb Port DSP/Ch Called # Codec Dial-peers

0x19E12 782 0x467EE400 0/0/0:15.4 0/2:4 224 g729r8 105/95

0x19E1E 787 0x467EE400 0/0/0:15.5 0/2:5 210 g711alaw 105/95

0x19E21 1C3A 0x46950E8C 0/0/1:15.31 0/2:2 *3139966251 g711alaw 200/103

0x19E26 78A 0x467EE400 0/0/0:15.8 0/6:3 210 g729r8 105/95

0x19E28 78B 0x467EE400 0/0/0:15.6 0/2:6 210 g729r8 105/95

0x19E36 78F 0x467EE400 0/0/0:15.1 0/2:3 210 g711alaw 105/95

0x19E38 790 0x467EE400 0/0/0:15.7 0/6:2 226 g729r8 105/95

0x19E3B 1C66 0x46950E8C 0/0/1:15.30 0/6:4 *3139966251 g711alaw 200/103

0x19E3E 792 0x467EE400 0/0/0:15.9 0/6:5 224 g729r8 105/95

0x19E40 793 0x467EE400 0/0/0:15.10 0/6:6 211 g711alaw 105/95

0x19E42 794 0x467EE400 0/0/0:15.11 0/11:1 226 g711alaw 105/95

0x19E45 1C78 0x46950E8C 0/0/1:15.29 0/2:1 *3139966251 None 200/103

12 active calls found

I want to monitor the total active calls found property !

Is there a toll/command to determine an OID for a specific show output ?

2 REPLIES
Cisco Employee

Re: Is there a way to determine the OID's for specific show comm

This might help:

---A-----

To get just the count of VoIP active calls the simplest way is to count

the number of entries that you get in the object cvVoIPCallActiveTable.

Sometimes this may not be accurate so it is good to verify that for each

entry in cvVoIPCallActiveTable, there is an entry in callActiveTable. If

not, drop those ones from the count.

To further refine this to distinguish between calls that are in

connecting, connected or active state you can use the

callActiveCallState in callActiveTable.

The oid used above are as follows :

CISCO-VOICE-DIAL-CONTROL-MIB: "cvVoIPCallActiveTable"

"1.3.6.1.4.1.9.9.63.1.3.2"

DIAL-CONTROL-MIB: "callActiveTable"

"1.3.6.1.2.1.10.21.1.3.1"

DIAL-CONTROL-MIB: "callActiveCallState"

"1.3.6.1.2.1.10.21.1.3.1.1.9"

Also for Historical data, the following looks promising :

CISCO-VOICE-DIAL-CONTROL-MIB: "cvCallHistoryTable"

"1.3.6.1.4.1.9.9.63.1.4.1"

-----B------

To get something similar to the information of the command "sh call

voice active brief" you could do something like what I have below: (have

provided the MIB info next to it, for easier understanding)

H323 leg

pid: pid:200

callActivePeerId.291909790.1 = INTEGER: 200

Answer

callActiveCallOrigin.291909790.1 = INTEGER: answer(2)

205

callActivePeerAddress.291909790.1 = STRING: 205

active

callActiveCallState.291909790.1 = INTEGER: active(4)

tx:/ tx:85515/13681843

callActiveTransmitPackets.291909790.1 = Gauge32: 85692

callActiveTransmitBytes.291909790.1 = Gauge32: 13710323

rx:/ rx:85441/13670560

callActiveReceivePackets.291909790.1 = Gauge32: 85621

callActiveReceiveBytes.291909790.1 = Gauge32: 13699680

For the Telephony leg

pid:1

callActivePeerId.291909815.1 = INTEGER: 1

Originate

callActiveCallOrigin.291909815.1 = INTEGER: originate(1)

93928027

callActivePeerAddress.291909815.1 = STRING: 93928027

active

callActiveCallState.291909815.1 = INTEGER: active(4)

tx:/ tx:85442/13670720

callActiveTransmitPackets.291909815.1 = Gauge32: 85619

callActiveTransmitBytes.291909815.1 = Gauge32: 13699360

rx:/ rx:85515/13681843

callActiveReceivePackets.291909815.1 = Gauge32: 85695

callActiveReceiveBytes.291909815.1 = Gauge32: 13710963

Community Member

Re: Is there a way to determine the OID's for specific show comm

I tried those OID's before but without any result ( do I need to do it on device or interface or ? )

113
Views
10
Helpful
2
Replies
CreatePlease to create content