Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

LMS 3.2 - All 7609's showing up as 7606's...

LMS 3.2 on Solaris 10.

I just realized that our 7609's are listed as 7606's. I just tried updating the device packages and didn't see anything pertaining to 7609's and they are still listed as 7606's.

Is there a device package for the 7609's? They have been around for a long time, I'm surprised there isn't a way to properly manage them with LMS.

Thanks,

  • Network Management
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: LMS 3.2 - All 7609's showing up as 7606's...

The bug for this was hard to find due to a bad headline, but you're seeing CSCsm83948.  This is fixed in 12.2(18)SXF14.

13 REPLIES
Cisco Employee

Re: LMS 3.2 - All 7609's showing up as 7606's...

Where are they showing up as 7606s?  What are the sysObjectIDs from these routers?

New Member

Re: LMS 3.2 - All 7609's showing up as 7606's...

We have the same issue.  The system object id for the 7609 is .1.3.6.1.4.1.9.1.863

It shows up as 7606.

Cisco Employee

Re: LMS 3.2 - All 7609's showing up as 7606's...

Chassis with this sysObjectID are 7606-S routers.  So LMS is correct.  If these are actually nine-slot chassis, then something is wrong on the device side.  The 7609 sysObjectIDs are 1.3.6.1.4.1.9.1.509 and 1.3.6.1.4.1.9.1.864.

New Member

Re: LMS 3.2 - All 7609's showing up as 7606's...

These are actually 9-slot chassis.  What could be wrong on the device side ?  Can the sysobjectid be modified ?

Cisco Employee

Re: LMS 3.2 - All 7609's showing up as 7606's...

No, the sysObjectID is built into the chassis.  I haven't been able to find a bug that explains this behavior.  Post a "show version" from one of these switches as well as a walk of the entPhysicalTable.

New Member

Re: LMS 3.2 - All 7609's showing up as 7606's...

Requested info is attached.

Cisco Employee

Re: LMS 3.2 - All 7609's showing up as 7606's...

The bug for this was hard to find due to a bad headline, but you're seeing CSCsm83948.  This is fixed in 12.2(18)SXF14.

New Member

Re: LMS 3.2 - All 7609's showing up as 7606's...

Great, we need to upgrade IOS to fix LMS...too bad this is on our key devices making outages nearly impossible.

As always, thanks for the information. You've helped me many, many times with my LMS questions!

Hall of Fame Super Silver

Re: LMS 3.2 - All 7609's showing up as 7606's...

LMS highlighting this bug is a mixed blessing.

On the other hand, you are running an aging IOS image (12.2(18)SXF17a is the current revision in that train - Release Notes) and the devices haven't been reloaded in over two years. As relatively high end key network devices, does your network design have redundancy built-in? A reload on a 7609 will cause that device and any services it provides to be offline for 1-2 minutes. You may be able to use that as a catalyst for design modification to remove the single point of failure (if such is indeed the case). You would also have the benefit of addressing other bug fixes which may not be so benign as the one Joe highlighted.

359
Views
0
Helpful
13
Replies