Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

LMS 3.2 with SNMP v3 not working

Hi ,

My network is currently running with SNMP v2 configured in easch devices. With snmp v2 our LMS 3.2 server is working fine. However we have planned to migrate our network to snmp v3 . I have configured my few devices for SNMP v3 and added them to my LMS server.

Except DFM module these new SNMP v3 devices are working fine in all other modules. In DFM these devices are reflecting under "snmp timeout" group.

I checked with device center -> management station to device; where the SNMP v3 connections are showing "okey"

following are tyhe configuration i have done in my devices.

snmp-server group v3g v3 priv read testr write testw

snmp-server user v3u v3g v3 auth md5 test123

snmp-server view testr iso in

snmp-server view testw iso in

snmp-server host 10.X.X.38 version 3 priv v3u

snmp-server user v3u v3g v3 auth md5 test1234 priv des56 test4321

snmp-server group v3g v3 priv read testr write testw

snmp-server user v3u v3g v3 auth md5 test123

snmp-server view testr iso in

snmp-server view testw iso in

snmp-server host 10.X.X.38 version 3 priv v3u

snmp-server user v3u v3g v3 auth md5 test1234 priv des56 test4321

followinfg are my module details.

LMS      : 3.2

CM        : 5.2

CV          :6.1.9

CS          :3.3.0

DFM     : 3.2.0

IPM     : 4.2.0

RME     : 4.3.0 

Everyone's tags (2)
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: LMS 3.2 with SNMP v3 not working

DFM behaves different than the other modules.

DES56 is not a supported privacy algorithm for DFM. You can use DES or AES128.

Supported Algorithms in DFM

The details of the algorithms supported in DFM are:

AuthNoPriv Mode — Supported Auth Algorithm: MD5 and SHA

AuthPriv Mode

Supported Auth Algorithm: MD5 and SHA

Supported Privacy Algorithm: DES and AES128

Unsupported Privacy Algorithm: 3DES, AES192, and AES256

For more details check :

http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_device_fault_manager/3.2/user/guide/useDevMg.html#wp1483766

-Thanks

Vinod

-Thanks Vinod **Rating Encourages contributors, and its really free. **
2 REPLIES
Cisco Employee

Re: LMS 3.2 with SNMP v3 not working

DFM behaves different than the other modules.

DES56 is not a supported privacy algorithm for DFM. You can use DES or AES128.

Supported Algorithms in DFM

The details of the algorithms supported in DFM are:

AuthNoPriv Mode — Supported Auth Algorithm: MD5 and SHA

AuthPriv Mode

Supported Auth Algorithm: MD5 and SHA

Supported Privacy Algorithm: DES and AES128

Unsupported Privacy Algorithm: 3DES, AES192, and AES256

For more details check :

http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_device_fault_manager/3.2/user/guide/useDevMg.html#wp1483766

-Thanks

Vinod

-Thanks Vinod **Rating Encourages contributors, and its really free. **

Re: LMS 3.2 with SNMP v3 not working

Thanks a lot.

It resolved my problem by changing the algorithm to DES.

826
Views
0
Helpful
2
Replies