Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

LMS config error

Hi

Following error was observed in cisco lms while configuring the config archive mgmt.

Please check and help.

17 REPLIES
Cisco Employee

Re: LMS config error

Post the output of the pdshow command.

New Member

Re: LMS config error

pls see the output of pdshow attached

Cisco Employee

Re: LMS config error

Please post the jrm.log.

New Member

Re: LMS config error

Pls find the logs attached...

Cisco Employee

Re: LMS config error

Please post the output of the DOS SET command.

New Member

Re: LMS config error

how will i get the output of DOS SET ??

and at which location ?

Cisco Employee

Re: LMS config error

Open a DOS prompt on the server, type the command SET, then capture the output.

New Member

Re: LMS config error

Please find the output attached

Cisco Employee

Re: LMS config error

Post a screenshot of the services control panel showing all of the CiscoWorks services. Then, shutdown the Daemon Manager, run the DOS command netstat -a -n -o -b, then post the output.

New Member

Re: LMS config error

services control panel ? how can i do that ? pls help

just to go to the folder and give you the screenshot ? or something else you are asking for.

Cisco Employee

Re: LMS config error

Open the Services control panel, and take screenshots of every page of it illustrating all services.

Then shutdown the CiscoWorks Daemon Manager service, and run netstat -a -n -o -b from a DOS prompt, and post the output.

New Member

Re: LMS config error

Pls check the attachments

Cisco Employee

Re: LMS config error

This is what I thought. Set the CiscoWorks Tomcat, CiscoWorks VisiBroker, DFM dfmInv database engine, DFM dfmEpm database engine, and DFM dfmFh database engine services to be Manual startup, then reboot the server. It should work properly when it comes back up.

New Member

Re: LMS config error

i should keep them for manual startup ? and then start all of these services manually , right ?

Cisco Employee

Re: LMS config error

They MUST be set to Manual startup. The Daemon Manager service is the only thing allowed to start these processes.

New Member

Re: LMS config error

Hi

i have made all the changes you have asked for, but still experiencing the same issue,

out of 7 (6509E) switches configured i am getting only traps from 1 switch.

previously we used to get from all 7 switches.

( Getting trap from single switch and that too repeated trap)

EVENT ID = 0001S8Z

ALERT ID = 00000UM

TIME = Wed 20-May-2009 09:35:51 IST

STATUS = Active

SEVERITY = Critical

MANAGED OBJECT = 172.20.110.163

MANAGED OBJECT TYPE = Switches and Hubs

EVENT DESCRIPTION = Unresponsive::Component=2.2.2.9 [172.20.110.163];IPStatus=TIMEDOUT;InterfaceName=IF-172.20.110.163/238 [Vl2] [2.2.2.9];InterfaceType=PROPVIRTUAL;InterfaceOperStatus=UP;NetworkNumber=2.2.2.8;InterfaceMode=NORMAL;InterfaceAdminStatus=UP;Address=2.2.2.9;

CUSTOMER IDENTIFICATION = NSE

Cisco Employee

Re: LMS config error

The initial problem had nothing to do with traps. This is a completely different issue.

If the JRM error is resolved, then start a new thread for the DFM problem. If the JRM problem is still occurring, then post the new pdshow and jrm.log as well as exactly what you're doing which results in the JRM error.

209
Views
0
Helpful
17
Replies
CreatePlease to create content