Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Need SNMP OID for MSTP status in Cisco SG300-28MP 28-port Gigabit Max-PoE Managed Switch

Hi,

I have configured redundant network using two Cisco SG300-28MP 28-port Gigabit Max-PoE Managed Switch through MSTP & it's working fine.

I need OID of MSTP status from which I can monitor which Switch is active and which one is in standby mode.

Please help.

Thanks,

Harsha 

Everyone's tags (1)
9 REPLIES
Cisco Employee

Hi Harsha, check these OID's

Hi Harsha,

 

check these OID's:

http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=1.3.6.1.4.1.9.9.500.1.2.1.1.6&translate=Translate&submitValue=SUBMIT

http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=cRFStatusUnitState&translate=Translate&submitValue=SUBMIT&submitClicked=true

 

Thanks-

Afroz

**Ratings Encourages Contributors ***

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

 Hello Afroz, Thanks for your

 

Hello Afroz,

 

Thanks for your reply.

The tree structure which I find while browsing the switch is different compared to the one you shared.

Also, when I queried for the OID mentioned in your message fetched no data from switch.

Please find the attached snapshot of the SNMP query for the switch.

 

Thanks,

Harsha

Cisco Employee

Hi Harsha, can you installed

Hi Harsha,

 

can you installed Net-snmp (download from google ) and then do the SNMP walk and see how it works

looks like  your tool does not have the correct MIB

Thanks-
 

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

Hi Afroz,Can you please brief

Hi Afroz,

Can you please brief me the steps for SNMP query like what all the prerequisites I need before querying the switch? currently I'm using My-soft  for querying the switch.

Thanks,

Harsha 

Cisco Employee

you just need to have snmp

you just need to have snmp community string defined on the device

 

for e.g  snmp-server community <community name > RO/ RW

 

SNMP WALK syntax::

 

snmpwalk -v2c -c <community name > <ip address>  <OID>

 

Thanks-

Afroz

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

As you said, its throwing an

As you said, its throwing an error "OID cannot be resolved through loaded MIB modules".

Please find the attached error snapshot.

Thanks,

Harsha

New Member

Hi Afroz, Am new to snmp but

Hi Afroz,

 

Am new to snmp but have basic knowledge .

Can you tel me where we find the oid's ?

regard's

Allamani

Cisco Employee

Hi Allamani,OID are part of

Hi Allamani,

OID are part of MIBS o they are bundle into  MIB.

 

if you are specific looking for some OID, you cab google and find it . also use the below link for : OID

http://tools.cisco.com/Support/SNMP/do/BrowseOID.do

 

Thanks

 

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****
New Member

Hi Afroz,I downloaded MIB

Hi Afroz,

I downloaded MIB file from the below link http://www.cisco.com/c/en/us/support/switches/sg300-28mp-28-port-gigabit-max-poe-managed-switch/model.html#~rdtab1

I'm unable to query the OID 1.3.6.1.4.1.9.9.500.1.2.1.1.6 through SNMP, kindly help.

 

Regards,

Harsha

1024
Views
8
Helpful
9
Replies