We have just purchased a number of the 2960s model switches. I have one 'odd-ball' version of the switches out right now, it is WS-C2960S-48TS-S. It can't get it to sync the archive. No other device is having problems. The error states to check the DCMA log, but there is nothing of note in there. Credentials pass, but testing the TFTP fails. Any ideas?
The switch is up and running properly (seemingly so anyway). I discovered the problem later when I was looking at LMS and noticed there was a unit that was not collecting its config. I updated the software to it and that did not help. (see version information below).
I have now also noticed that it does not seem to understand 'ip dhcp snooping'.
Here is the switch version information:
Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2010 by Cisco Systems, Inc. Compiled Sat 07-Aug-10 23:21 by prod_rel_team Image text-base: 0x00003000, data-base: 0x01B00000
ROM: Bootstrap program is Alpha board boot loader BOOTLDR: C2960S Boot Loader (C2960S-HBOOT-M) Version 12.2(53r)SE, RELEASE SOFTWARE (fc3)
ACCESS-202N25-2960-01 uptime is 15 hours, 21 minutes System returned to ROM by power-on System restarted at 17:59:52 DST Mon Nov 1 2010 System image file is "flash:/c2960s-universalk9-mz.122-55.SE/c2960s-universalk9-mz.122-55.SE.bin"
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to email@example.com. WS-C2960S-48TS-S (PowerPC) processor (revision B0) with 131072K bytes of memory. Processor board ID FOC1431Z1G6 Last reset from power-on 1 Virtual Ethernet interface 1 FastEthernet interface 50 Gigabit Ethernet interfaces The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address : E8:04:62:1E:76:80 Motherboard assembly number : 73-12424-06 Power supply part number : 341-0327-01 Motherboard serial number : FOC14311LHX Power supply serial number : LIT14250NQD Model revision number : B0 Motherboard revision number : A0 Model number : WS-C2960S-48TS-S Daughterboard assembly number : 73-11933-04 Daughterboard serial number : FOC14312467 System serial number : FOC1431Z1G6 Top Assembly Part Number : 800-32452-02 Top Assembly Revision Number : A0 Version ID : V02 CLEI Code Number : COMGK00ARB Daughterboard revision number : A0 Hardware Board Revision Number : 0x01
Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 50 WS-C2960S-48TS-S 12.2(55)SE C2960S-UNIVERSALK9-M
[toc:faq]The ProblemOn traditional switches whenever we have a trunk
interface we use the VLAN tag to demultiplex the VLANs. The switch needs
to determine which MAC Address table to look in for a forwarding
decision. To do this we require the switch to do...
[toc:faq]Introduction:Netdr is a tool available on a RSP720, Sup720 or
Sup32 that allows one to capture packets on the RP or SP inband. The
netdr command can be used to capture both Tx and Rx packets in the
software switching path. This is not a substitut...
IntroductionOSPF, being a link-state protocol, allows for every router
in the network to know of every link and OSPF speaker in the entire
network. From this picture each router independently runs the Shortest
Path First (SPF) algorithm to determine the b...