Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Nexus 7K Sup Mod Online Diag Status Fail

My Nexus 7K Sup module status shows fail but the module is active. I am trying to redo the diagnosis but can seem to get the command to work on the NX-OS. I have shared the show commands below. 

Kindly advise if any of you come across such situation. The Online Diag Status  shows fail, but the module is active. How I can restore it with out a reboot?

 

Mod  Ports  Module-Type                         Model              Status
---  -----  ----------------------------------- ------------------ ----------
1    32     10 Gbps Ethernet XL Module          N7K-M132XP-12L     ok
2    32     10 Gbps Ethernet XL Module          N7K-M132XP-12L     ok
3    48     10/100/1000 Mbps Ethernet Module    N7K-M148GT-11      ok
5    0      Supervisor module-1X                N7K-SUP1           active *
6    0      Supervisor module-1X                N7K-SUP1           ha-standby

Mod  Sw              Hw
---  --------------  ------
1    5.2(4)          1.3     
2    5.2(4)          1.3     
3    5.2(4)          1.8     
5    5.2(4)          2.1     
6    5.2(4)          2.1     

Mod  Online Diag Status

---  ------------------
1    Pass
2    Pass
3    Pass
5    Fail
6    Pass

Xbar Ports  Module-Type                         Model              Status
---  -----  ----------------------------------- ------------------ ----------
1    0      Fabric Module 1                     N7K-C7010-FAB-1    ok
2    0      Fabric Module 1                     N7K-C7010-FAB-1    ok
3    0      Fabric Module 1                     N7K-C7010-FAB-1    ok
4    0      Fabric Module 1                     N7K-C7010-FAB-1    ok
5    0      Fabric Module 1                     N7K-C7010-FAB-1    ok

Xbar Sw              Hw
---  --------------  ------
1    NA              1.1     
2    NA              1.1     
3    NA              1.1     
4    NA              1.1     
5    NA              1.1     

-----------------------------------------------------------------------------------------

sh module 5

Mod  Ports  Module-Type                         Model              Status
---  -----  ----------------------------------- ------------------ ----------
5    0      Supervisor module-1X                N7K-SUP1           active

Mod  Sw              Hw
---  --------------  ------
5    5.2(4)          2.1     

 

Mod  Online Diag Status
---  ------------------
5    Fail

------------------------------------------------------------------------------------------------


Software
  BIOS:      version 3.22.0
  kickstart: version 5.2(4)
  system:    version 5.2(4)
  BIOS compile time:       02/20/10
  kickstart image file is: bootflash:///n7000-s1-kickstart.5.2.4.bin
  kickstart compile time:  12/25/2020 12:00:00 [03/08/2012 06:58:13]
  system image file is:    bootflash:///n7000-s1-dk9.5.2.4.bin
  system compile time:     1/28/2012 23:00:00 [03/08/2012 07:59:07]

 

Br,

Rushan

 

6 REPLIES
New Member

Solved!!! I had to get on the

Solved!!! I had to get on the management VDC and redo the tests and it all worked.

New Member

how do you redo the test?

how do you redo the test?  can it be done online?  my sup module is showing the same failed state.

New Member

Get on to the Management VDC

Get on to the Management VDC and run the "diagnostic clear result" the run the diagnostic test again [non-disruptive]. Then you should get a "pass" result unless it really failed. 

New Member

I do the command , but the

I do the command , but the problem is always still there , 

Mod  Online Diag Status
---  ------------------
7    Fail

 i changed the Module with a new one ==> problem always there 

 i Changed the slot on the switch ==> problem always there 

 

do you have an idee ? 

best regards 

 

 

New Member

We upgraded, seemed to solve

We upgraded, seemed to solve the issue as it has not recurred. Did not need hardware replacements, even though they sent a chassis.

New Member

I have had this on several

 

                                                                                       

3734
Views
0
Helpful
6
Replies