Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

PBR - adding a route map to an interface

Hello.

I cannot add a route-map to an interface on a C3750 stack

I have copied the switch details below

#sho ver
Cisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 19-Jul-07 19:15 by nachen
Image text-base: 0x00003000, data-base: 0x01280000

ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(25r)SEE3, RELEASE SOFTWARE (fc1)

Pleidelsheim_V1B_Core uptime is 16 hours, 43 minutes
System returned to ROM by power-on
System restarted at 22:01:48 CET Wed Mar 3 2010
System image file is "flash:/c3750-ipservices-mz.122-35.SE5.bin"

cisco WS-C3750G-24TS (PowerPC405) processor (revision P0) with 118784K/12280K bytes of memory.
Processor board ID CAT1130ZK5F
Last reset from power-on
9 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : 00:1D:46:8C:22:80
Motherboard assembly number     : 73-7058-14
Power supply part number        : 341-0045-01
Motherboard serial number       : CAT113059LV
Power supply serial number      : PHI1114L1PJ
Model revision number           : P0
Motherboard revision number     : A0
Model number                    : WS-C3750G-24TS-E
System serial number            : CAT1130ZK5F
Top Assembly Part Number        : 800-22348-07
Top Assembly Revision Number    : A0
Version ID                      : V07
CLEI Code Number                : COM7700ARA
Hardware Board Revision Number  : 0x09


Switch   Ports  Model              SW Version              SW Image
------   -----  -----              ----------              ----------
*    1   28     WS-C3750G-24TS     12.2(35)SE5             C3750-IPSERVICES-M
     2   28     WS-C3750G-24TS     12.2(35)SE5             C3750-IPSERVICES-M


Switch 02
---------
Switch Uptime                   : 16 hours, 43 minutes
Base ethernet MAC Address       : 00:21:A1:2E:78:00
Motherboard assembly number     : 73-7058-15
Power supply part number        : 341-0045-01
Motherboard serial number       : FDO121903D2
Power supply serial number      : LIT121603VV
Model revision number           : Q0
Motherboard revision number     : A0
Model number                    : WS-C3750G-24TS-E
System serial number            : CAT1105RGN2
Top assembly part number        : 800-22348-08
Top assembly revision number    : A0
Version ID                      : V08
CLEI Code Number                : COMUJ10ARA

Configuration register is 0xF

#sho sdm prefer
The current template is "desktop routing" template.
The selected template optimizes the resources in
the switch to support this level of features for
8 routed interfaces and 1024 VLANs.

  number of unicast mac addresses:                  3K
  number of IPv4 IGMP groups + multicast routes:    1K
  number of IPv4 unicast routes:                    11K
    number of directly-connected IPv4 hosts:        3K
    number of indirect IPv4 routes:                 8K
  number of IPv4 policy based routing aces:         0.5K
  number of IPv4/MAC qos aces:                      0.5K
  number of IPv4/MAC security aces:                 1K

When I try to add the route map

interface Vlanx
ip policy route-map xx

%PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map xx not supported for Policy-Based Routing

Can anyone see what could be wrong?

1 REPLY
New Member

Re: PBR - adding a route map to an interface

Okay, just realised the route-map is not valid.

The settings are okay.

access-list 160 remark WIRELESS GUEST PBR FWD TRAFFIC
access-list 160 permit tcp 172.16.168.128 0.0.0.63 any
access-list 160 permit udp 172.16.168.128 0.0.0.63 any
access-list 160 permit ip 172.16.168.128 0.0.0.63 any
access-list 160 permit icmp 172.16.168.128 0.0.0.63 any

route-map GUEST_VLAN-to-WEB permit 20
description FWD REMAINING GUEST TRAFFIC TO PROXY
match ip address 160
set interface Null0

Doesn't like the set interface Null0

How else could I setup a black hole

1996
Views
0
Helpful
1
Replies