Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Pushing FPD software to nodes using LMS

I am trying to deploy FPD software to the sup-bootflash: on a number of 7600s. I have the software on one node as a tftp-server, and am trying the following netconfig job in enable mode

copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:

The job fails with the following error:

Command(s) failed on the device Insufficient no. of interactive responses(or timeout) for command: copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:. TFTP: Tftp is supported only for config mode commands. Insufficient no. of interactive responses(or timeout) for command: copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:.

I assume it's because the node is probably prompting something similar to Destination filename [c7600-fpd-pkg.122-33.SRC2.pkg]?

and expecting a <CR>..

Is there a way to send one in a netconfig job? Is there a better way to distribute FBD software to the 7600s?

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: Pushing FPD software to nodes using LMS

You can use interactive commands in Netconfig. Just add a "" anywhere a response is expected. For example:

copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:

If additional responses are required, specify them after the . For example:

copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:172.25.255.7c7600-fpd-pkg.122-33.SRC2.pkgsup-bootdisk:

6 REPLIES
Cisco Employee

Re: Pushing FPD software to nodes using LMS

What version of RME is this?

New Member

Re: Pushing FPD software to nodes using LMS

RME 4.2.0

Cisco Employee

Re: Pushing FPD software to nodes using LMS

You can use interactive commands in Netconfig. Just add a "" anywhere a response is expected. For example:

copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:

If additional responses are required, specify them after the . For example:

copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:172.25.255.7c7600-fpd-pkg.122-33.SRC2.pkgsup-bootdisk:

New Member

Re: Pushing FPD software to nodes using LMS

I added the at the end, but still get the same error.

Command(s) failed on the device Insufficient no. of interactive responses(or timeout) for command: copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:. TFTP: Tftp is supported only for config mode commands. Insufficient no. of interactive responses(or timeout) for command: copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:.

I thought it might be a time out issue, so I set the timeout to 600 seconds (the transfer takes about 180 seconds).

Does this come into play?

TFTP: Tftp is supported only for config mode commands.

I am doing the job from enable mode, as I would in person.

Cisco Employee

Re: Pushing FPD software to nodes using LMS

That's fine. Exactly what does your template look like now, and when done manually, what prompts do you see?

New Member

Re: Pushing FPD software to nodes using LMS

When recreating the sequence manually, I found a second (Do you want to overwrite) prompt as I had manually done the transfer.

All is working. Thanks for the help!

319
Views
0
Helpful
6
Replies
CreatePlease login to create content