Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

QPM 4.1.4 issues

Hi all,

I've upgraded from 4.1.3 to 4.1.4 and now in QoS Report Card I don't see some classes of nested policies which were displayed in 4.1.3. Rediscover or add/delete of devices doesn't help.

Can I see somewhere in the logs where could be the problem or just to deinstall 4.1.4 patch (which I'm not sure how to do)

Any help or advice is very appreciated,

Ivana

8 REPLIES

Re: QPM 4.1.4 issues

Hi Ivana

Are you still facing this issue? does anyone from Cisco responded to your concern? I am also facing the same issue after upgrading to QPM 4.1.4.

Anyone from Cisco, please do reply.

Thanks,

Arnold

New Member

Re: QPM 4.1.4 issues

Hi Arnold,

I went back to 4.1.3

From: "aamadulin.accenture"

To: Ivana Kvaka

Date: 03.11.2010 10:02

Subject: New message: "QPM 4.1.4 issues"

ivana.kvaka,

A new message was posted in the Discussion thread "QPM 4.1.4 issues":

https://supportforums.cisco.com/message/3217096#3217096

Author : aamadulin.accenture

Profile : https://supportforums.cisco.com/people/aamadulin.accenture

Message:

Cisco Employee

Re: QPM 4.1.4 issues

Hello Ivana,

Please post some information about the device ("show ver") and whic policies are not appearing. A snippet from the "snow run" showing the configuration should help.

Thanks!

Curtis

New Member

Re: QPM 4.1.4 issues

Hi ccarring,

We needed QPM to work, and I've returned QPM back to 4.1.3 and all nested policies were visible again. Unfortunately,  I don't remember in 4.1.4 which were not visible.

thank you,

ivana

New Member

Re: QPM 4.1.4 issues

We have also had this issue occur.  From what the SE is relaying to us that a new patch QPM 4.1.5 should be out in December of this year that addresses this issue.

New Member

Re: QPM 4.1.4 issues

Hi Scott,

That's great info. Do you people know, when you encounter problem, is there a possibility to deinstall just patch (not the entire QPM, as I did)

thank you,

ivana

New Member

Re: QPM 4.1.4 issues

Since we have a support agreement with Cisco I was given a patch and a process.  Regretfully I can not post the patch.

The process is as follows but may not work without the patch

1) Goto QPM server and open
C:\PROGRA~1\CSCOpx\MDC\tomcat\webapps\cwhp\WEB-INF\classes\dcr-schema.xml
file in a text editor

2) Goto line with text
groupable="yes" displayable="no" returnable="yes">.
With no other changes to this file, this line should be present at line #83
or around that.

3) In the above line, change text displayable="no" to displayable="yes" i.e
change only the word "no" to "yes". So, the line will be changed from


displayable="no" returnable="yes">

to


displayable="yes" returnable="yes">


Highlighted the text in bold that will be changed to new value. After making
the above change, save file and close the text editor.

New Member

Re: QPM 4.1.4 issues

Hi,

This process you've sent, is it for installing or deinstalling patch? And patch is 4.1.4 or 4.1.5?

thank you,

Ivana

405
Views
0
Helpful
8
Replies
CreatePlease to create content