Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Query about accessing WiSM in Cat 6509 through session slot command

Hi,

I have following setup in production.

1.Cat 6509 having IOS 12.2(18)SXF8

2.WiSM module installed in slot 8 (Ver: 5.2.157.0)

The setup is working smoothly , I am able to manage the WiSM module through GUI, Module console but not through Session Slot 8 Processor 1 and 2 command.

Attaching the outputs and errors..........

#session slot 8 processor 1

The default escape character is Ctrl-^, then x.

You can also type 'exit' at the remote prompt to end the session

Trying 192.168.197.11 ...

% Connection timed out; remote host not responding

#sh module

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP      

  2    8  CEF720 8 port 10GE with DFC            WS-X6708-10GE     

  4    8  Network Analysis Module                WS-SVC-NAM-2      

  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3B      

  7   48  48 port 10/100/1000mb EtherModule      WS-X6148-GE-TX    

  8   10  WiSM WLAN Service Module               WS-SVC-WISM-1-K9  

  9   48  48 port 10/100/1000mb EtherModule      WS-X6148-GE-TX    

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  0013.c31b.0a70 to 0013.c31b.0a87   2.4   12.2(14r)S5  12.2(18)SXF8 Ok

  2  0021.a0ef.7710 to 0021.a0ef.7717   1.6   12.2(18r)S1  12.2(18)SXF8 Ok

  4  0019.306d.339e to 0019.306d.33a5   4.2   7.2(1)       3.5(1a)      Ok

  5  0017.9444.cd10 to 0017.9444.cd13   5.4   8.4(2)       12.2(18)SXF8 Ok

  7  001d.450e.fed0 to 001d.450e.feff   7.2   7.2(1)       8.5(0.46)RFW Ok

  8  0025.8438.2284 to 0025.8438.2293   2.3   12.2(14r)S5  12.2(18)SXF8 Ok

  9  0017.9440.d358 to 0017.9440.d387   7.0   7.2(1)       8.5(0.46)RFW Ok

Mod  Sub-Module                  Model              Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

  1  Centralized Forwarding Card WS-F6700-CFC       SAL0917A6FY  2.1    Ok

  2  Distributed Forwarding Card WS-F6700-DFC3C     SAL1310LFXE  1.2    Ok

  5  Policy Feature Card 3       WS-F6K-PFC3B       SAL1126SKZS  2.3    Ok

  5  MSFC3 Daughterboard         WS-SUP720          SAL1126SNL1  3.0    Ok

  8  Centralized Forwarding Card WS-SVC-WISM-1-K9-D SAD1335000J  2.1    Ok

Mod  Online Diag Status

---- -------------------

  1  Pass

  2  Pass

  4  Pass

  5  Pass

  7  Pass

  8  Pass

  9  Pass


#sh wism status
Service Vlan : 160, Service IP Subnet : 192.168.197.3/255.255.255.224
      WLAN
Slot  Controller  Service IP       Management IP    SW Version  Status
----+-----------+----------------+----------------+-----------+---------------
8     1           192.168.197.11     192.168.198.15     5.2.157.0   Oper-Up
8     2           192.168.197.12     192.168.198.16     5.2.157.0   Oper-Up
#sh wism module 8 controller 1 status
WiSM Controller 1 in Slot 8
Operational Status of the Controller : Oper-Up
Service VLAN                         : 160
Service Port                         : 9
Service Port Mac Address             : 0026.cb0a.3fa2
Service IP Address                   : 192.168.197.11
Management IP Address                : 192.168.198.15
Software Version                     : 5.2.157.0
Port Channel Number                  : 297
Allowed vlan list                    : 65,90-91,106,160
Native VLAN ID                       : 961
WCP Keep Alive Missed                : 0
#sh wism module 8 controller 2 status
WiSM Controller 2 in Slot 8
Operational Status of the Controller : Oper-Up
Service VLAN                         : 160
Service Port                         : 10
Service Port Mac Address             : 0026.cb0b.71e2
Service IP Address                   : 192.168.197.12
Management IP Address                : 192.168.198.16
Software Version                     : 5.2.157.0
Port Channel Number                  : 298
Allowed vlan list                    : 90-91,106,160-962
Native VLAN ID                       : 961
WCP Keep Alive Missed                : 0

5 REPLIES
Hall of Fame Super Gold

Re: Query about accessing WiSM in Cat 6509 through session slot

I remembered reading a bug in the 5.2.157.0 about this.  Can you avoid using the 5.X?  It's known to be bug-ridden.

Community Member

Re: Query about accessing WiSM in Cat 6509 through session slot

I have searched the related BUG but nothing related found. Do you have the bug ID?

Community Member

Re: Query about accessing WiSM in Cat 6509 through session slot

I have the same problem on version 4.2.205.0.  I haven't consoled into the WiSM locally yet, but the session should work before setting up intial configs.

Service Vlan : 9, Service IP Subnet : 10.7.4.254/255.255.255.0
      WLAN
Slot  Controller  Service IP       Management IP    SW Version  Status
----+-----------+----------------+----------------+-----------+---------------
7     1           10.7.4.2         169.254.1.1      4.2.205.0   Oper-Up
7     2           10.7.4.1         169.254.1.1      4.2.205.0   Oper-Up

#session slot 7 proc 2
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
Trying 10.7.4.1 ...
% Connection timed out; remote host not responding

Community Member

Re: Query about accessing WiSM in Cat 6509 through session slot

Have you found any solution?

Community Member

Re: Query about accessing WiSM in Cat 6509 through session slot

Yes, my solution was to remove the ip telnet source-interface Loopback0 command.   Then it worked.

-Brian

1234
Views
0
Helpful
5
Replies
CreatePlease to create content