Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

show interface problem

hi

i'm having a weird problem on my router

the interface is down ,down but i see input packets increasing and traffic is passing via this interface.

i would like to mention that the interface is working good. the problem it's showing down,down.

i added output from the router :

PT_Access-A_A6#sh int s0/2/2

Serial0/2/2 is down, line protocol is down

Hardware is HWIC-Serial

Description: GLX1120 CDM600

Interface is unnumbered. Using address of FastEthernet0/0 (10.0.0.20)

MTU 1500 bytes, BW 2048 Kbit, DLY 20000 usec,

reliability 255/255, txload 1/255, rxload 235/255

Encapsulation HDLC, loopback not set

Keepalive not set

Last input 00:00:58, output 3w1d, output hang never

Last clearing of "show interface" counters 00:00:06

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: weighted fair

Output queue: 0/1000/64/0 (size/max total/threshold/drops)

Conversations 0/1/256 (active/max active/max total)

Reserved Conversations 0/0 (allocated/max allocated)

Available Bandwidth 1536 kilobits/sec

5 minute input rate 3947000 bits/sec, 2722 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

18375 packets input, 3480198 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

DCD=up DSR=down DTR=up RTS=up CTS=down

if any one encountered this issue and has some inputs i will appreciate it.

thanks in advance

5 REPLIES
Cisco Employee

Re: show interface problem

Post the show ver from this device.

New Member

Re: show interface problem

hi,

i will post the sh ver tomorrow when i'm in the office.

please note that i have other serial interfaces on this router functioning normally.

New Member

Re: show interface problem

hi,

here is the sh run from this router :

PT_Access-A_A6#sh ver

Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Wed 22-Mar-06 18:40 by pwade

ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)

ROM: Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3c), RELEASE SOFTWARE (fc1)

PT_Access-A_A6 uptime is 24 weeks, 3 days, 5 hours, 21 minutes

System returned to ROM by power-on

System restarted at 23:38:32 UTC Sun Feb 8 2009

System image file is "flash:c2800nm-ipbase-mz.123-14.T7.bin"

Cisco 2811 (revision 53.51) with 245760K/16384K bytes of memory.

Processor board ID FCZ100871WB

2 FastEthernet interfaces

16 Serial(sync/async) interfaces

16 Low-speed serial(sync/async) interfaces

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

New Member

Re: show interface problem

i mean sh ver and not sh run as i posted previously

Cisco Employee

Re: show interface problem

I couldn't find a bug that matches this scenario exactly. I saw a few that had some similarities, but this looks like it might be a new issue. I suggest you contact TAC to have them analyze this further.

161
Views
0
Helpful
5
Replies