Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

SNMP and Temperature

I changed the temp thresholds from their default value of around 54 to 23 degrees below the RED threshold making the YELLOW threshold 42.  Now when I do this:

#sh env st
SWITCH: 1
FAN is OK
TEMPERATURE is OK
Temperature Value: 47 Degree Celsius
Temperature State: YELLOW
Yellow Threshold : 42 Degree Celsius
Red Threshold    : 65 Degree Celsius
POWER is OK
RPS is NOT PRESENT

SWITCH: 2
FAN is OK
TEMPERATURE is OK
Temperature Value: 45 Degree Celsius
Temperature State: YELLOW
Yellow Threshold : 42 Degree Celsius
Red Threshold    : 65 Degree Celsius
POWER is OK
RPS is NOT PRESENT

You can see that it says the temperature state is YELLOW.

Now when I poll SNMP this is what I get:

Temperature sensor 'SW#1, Sensor#1, GREEN ' is in 'Normal' state.
Current value: 47, threshold value: 65

Temperature sensor 'SW#2, Sensor#1, GREEN ' is in 'Normal' state.
Current value: 45, threshold value: 65

So I never get an alert that the switch is out of GREEN threshold. 

I am using WhatsUp Gold V16.1.3 for my monitoring application.

The switches that this is occuring on are stacked 3750G's running c3750-advipservicesk9-mz.122-46.SE.bin IOS.

Thank you.

12 REPLIES
New Member

SNMP and Temperature

check whcih switches modules,

New Member

SNMP and Temperature

Sorry, I'm not sure what you mean.

SNMP and Temperature

Dear Brandon McCreavy,

I am using Cisco Prime Infratructure to monitor Stacked C3750, C2960, 6504E.

I even cannot get device's temperature.

Could you please share which specific MIB that you used to get Switch's temperature?

Thanks & Regards

New Member

SNMP and Temperature

Here are the MIBs that I am looking at

1.3.6.1.4.1.9.9.13.1.3.1.2

1.3.6.1.4.1.9.9.13.1.3.1.3

1.3.6.1.4.1.9.9.13.1.3.1.4

1.3.6.1.4.1.9.9.13.1.3.1.6

Thank you

SNMP and Temperature

Thank McCreary,

So all above OIDs are included in CISCO-ENVMON-MIB.

I know that I asked very basic question.

I used many NMS software, all of them display devices (cisco sw) temperature immediately however my Cisco PI 1.3 cannot display it.

Best Regards

New Member

SNMP and Temperature

please configure

like this

Snmp-server enable traps envmon fan shutdown supply temperature status

rate it,

SNMP and Temperature

Hi Aman,

Thanks.

But it not work for me.

Please take a look to my picture.

Best Regards.

New Member

SNMP and Temperature

See the configuration , and configure it

snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart

snmp-server enable traps transceiver all

snmp-server enable traps tty

snmp-server enable traps (eigrp, ospf like this)

snmp-server enable traps fru-ctrl

snmp-server enable traps entity

snmp-server enable traps ether-oam

snmp-server enable traps flash insertion removal

snmp-server enable traps cpu threshold

snmp-server enable traps rep

snmp-server enable traps vtp

snmp-server enable traps vlancreate

snmp-server enable traps vlandelete

snmp-server enable traps envmon fan shutdown supply temperature status

snmp-server enable traps port-security

snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config

snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up

snmp-server enable traps ethernet cfm alarm

snmp-server enable traps event-manager

snmp-server enable traps rf

snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency

snmp-server enable traps config-copy

snmp-server enable traps config

snmp-server enable traps config-ctid

snmp-server enable traps hsrp

snmp-server enable traps ipmulticast

snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message

snmp-server enable traps bridge newroot topologychange

snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency

snmp-server enable traps syslog

snmp-server enable traps vlan-membership

snmp-server enable traps mac-notification change move threshold

*Plz do rate this post if you found it helpful*

SNMP and Temperature

Thanks.

My problem is that the teperature is not display on Cisco PI 1.3.

Of course, if I use other Monitoring Software, I can easilly get this information by 02 ways: SNMP polling or TRAP as you suggest.

Best Regards

SNMP and Temperature

Anyone else please help?

Cisco Employee

SNMP and Temperature

Hi Cuong

PI should show temp. utilization by default in TOP N ENV TEMP dashlet.

Can you tell which devices are managed and their IOS version?

SNMP and Temperature

Dear Mahabir,

It does not work for me.

Please check help me:

Cisco Catalyst 2960S: Software  15.0(2) SE4

Cisco Catalyst 3750-X Stack Switch: Software: 15.0(2) SE4

Cisco Catalyst 6504-E (Used VSS): Software: 15.1(1) SY1

Thanks & Best Regards

Cuong

2699
Views
3
Helpful
12
Replies